a. Determine the design moment capacity of the reinforced concrete beam shown in Figure 1(a) if it is reinforced with 4-28-mm diameter in tensio and 2-16-mm diameter in compression. b. If the beam will carry the loading pattern shown in Figure 1(b), what safe load W can it carry based on the design moment in part (a)?

a. Determine the design moment capacity of the reinforced concrete beam shown in Figure 1(a) if it is reinforced with 4-28-mm diameter in tensio and 2-16-mm diameter in compression. b. If the beam will carry the loading pattern shown in Figure 1(b), what safe load W can it carry based on the design moment in part (a)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tubular steel strut 2 m long, both ends hinged, must have a buckling load of120 kN, based on the Euler formula. The outside diameter is 60 mm. Calculatethe thickness required. What will be the factor of safety according to Rankine's formula if yield strength = 350 MPa and Rankine's constant is 1/7500 for hinged ends? (E = 200 GPa.)
Find the maximum uniform load w kN/m that can be applied on the beam shown in figure. so that the beam will not be cracked. Use n = 8.6 and fr = 3.4 MPa. Neglect the beam weight.
A beam is supported by a column 3 m tall with dimensions a x 1.5a as shown above. The column is fixed at the base and pinned to the beam. Assume a Young’s modulus of ? = 25 GPa and yield strength of ?? = 20 MPa for the column.a) Draw the SFD and BMD for the beam and determine the axial load acting on the column.b) What is the minimum value of “a” that would not result in buckling of the column?c) If the column was instead fixed to the beam, how would this change the minimum value of “a”?
A tubular steel strut 2 m long, both ends hinged, must have a buckling load of120 kN, based on the Euler formula. The outside diameter is 60 mm. Calculatethe thickness required. What will be the factor of safety according to Rankine's formula if oc = 350 MPa and Rankine's constant is 1/7500 for hinged ends? (E = 200 GPa.)
Problem 4. A reinforced concrete beam having a simple span of 8m is reinforced for tension with 25mm dia bars (As = 1963 mm2). The beam has a width of 350mm and an effective depth of 690 mm. Use f'c = 20.7 MPa, fy = 414 MPa. a. Determine the location of the neutral axis measured from the top outermost compression fiber of the section. Ans.: Blank 1 mm b. Determine the ultimate moment capacity of the beam. Ans.: Blank 1 kN.m. c. Determine the safe uniform live load (in kN/m) that the beam could carry. Assuming weight of concrete is 24 kN/cu.m. Ans.: Blank 1 kN/m
Problem #3: A circular shaft, fixed to the wall, is loaded as indicated in the figure below. Using all three failure criteria (Rankine's theory, Tresca criterion, and Von Mises criterion), determine the load magnitude, R, that causes yielding at point A on the cross-section. Assume the yield strength of the material is 64 ksi. Notes: . . ● Point A is at the mid-depth of the section and on the leftmost fiber (as viewed below). At the fixed base, the shaft will be subjected to a bending moment, a torsional moment, a shear force, and a normal force. Recall for a circular cross-section; 1=d¹ and/=d. Q does not need to be provided, as you should see herein. A 3 ft R 4 in. F T 2 ft 12R X
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi, α= 2.9 × 10−6 /°F] bar (1) and an aluminum alloy [E = 10,000 ksi, α= 12.5 × 10−6 /°F] bar (2), below. Each bar has a cross-sectional area of 2.00 in.2 . The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 26 kips is applied and the temperature is increased to 100°F, determine: (a) the normal stresses in bars (1) and (2). (b) the vertical deflection of joint D.
The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: Given: b(mm) = 250 h(mm) = 400 w(kN/m) = 15 Mb(kN-m) = 45 Using area moment method, determine the following: 1. Vertical reaction at A, RA. 2. Moment reaction at A, MA. 3. Flexural rigidity of the beam in N-mm^2 4. Rotation at B, in degrees. 5. Rotation at C. in degrees. 6. Deflection at B in mm. 7. Maximum deflection of the beam in mm. 8. If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN.
1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the modulus of elasticity (MPa) of the material. Assume the material does not yield.2. A truck is moving along 20 m. Span of beam. The front axle load is 8 kN, the middle load is spaced at 3 m from the front and 6 m from the rear. Determine the max. Moment produced by the load.3. A helical spring is made by wrapping steel wire 20 mm in diameter around a forming cylinder 150 mm in diameter. Compute number of turns required to permit an elongation of 132 mm without exceeding a shearing stress of 184.8 MPa. Use G = 83 GPa.
Find the maximum concentrated load P kN that can be applied on the beam shown in fig. (3), so that the beam will not be cracked. Use n = 8.6 and fr = 3.4 MPa. Neglect the beam weight
The section of a double tee (DT) prestress concrete joist is shown in Figure. The joists are simply supported on a span of 7.5m and are pre-tensioned with total initial force of 1100 kN from low-relaxation strands. The joist supports a total dead load of 2.3 kPa (including beam weight) and live load of 6.2 kPa. There is a loss of prestress of 20% at service loads. Unit weight of concrete is 24 kN/m^3a. Calculate the stress at the top fibers of the DT at end span due to initial pre-stressing force only.b. Calculate the compressive stress at the bottom fibers of the DT at midspan due to initial pre-stressing force only.c. Calculate the additional load in kPa such that the stress at the bottom fibers of the DT at midspan (due to service loads and prestress force) will be zero.
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k