a.) Explain CAD system architecture with neat sketch.  b.) Discuss the applications of CAD and CAM in the manufacturing environment

Q: Determine the mass products of inertia Ixy, Iyz, and Izx of the cast aluminum machine component…

A: Solution: Given Data: ρ=2700 kg/m3   To Find: The mass products of inertia Ixy, Iyz and Izx.

Q: Draw an orthorhombic unit cell having 210 planes

A: According to the given data Miller indices=210 We need to draw The Plane in the unit cell

Q: A member of your team gives you the following MATLAB program. Your job is to create the function…

A: Given: Height, H=30 cm Volume, V=50 cm3 MATLAB code: R2=RadiusCone(H,V)

Q: A vertical reducing bend carries 0.455 m^3/s of water at a pressure of 148kPa entering the bend at…

A: Given-Information:-  Q= 0.455 m3/sp1 = 148 kpadA = 0.6 mdB = 0.3 mF = 35670 Nθ = 45° To-Determine:-…

Q: 1)List three ways of operating a 5/2 way directional control valve

A: Ans-  Directional control valves are the devices which let the fluids flow from valve ports to the…

Q: Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal…

A: Input speed of belt N1=1750rpm, Output speed of belt N2=725rpm,Belt Linear VelocityVb=4000ft/min…

Q: In a production facility, 1.6-in-thick 2-ft x 2-ft square brass plates (p = 532.5 lbm/ft³ and Cp =…

A: Given:   The thickness of plate (t) = 1.6 in The area of plate A = 4 ft2 The density of plate (ρ) =…

Q: E10.5 Deriving shape factors for stiffness-limited design (Figure E10.4). Derive the expression for…

A: given data: h1 = 10t h2 = 8t

Q: Oscillator BA rises with speed v and deceleration a, as shown in the figure. The cause of the…

A: The speed of the oscillator BA is v in vertically upward direction. And deceleration is a hence the…

Q: Problem 1: Three vertical posts AD, BE, and CF are held between two horizontal rigid plates. Posts…

A:

Q: Q1 If the atmosphere is 50 km thick, and the atmospheric pressure at sea level is approximately 101…

A: Atmosphere thickness = 50 km = 50000 m. Atmospheric pressure at sea level is approximately = P= 101…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 214 mm and a…

A: Given For segment (1)           Outer diameter do1=214 mm=0.214 mWall Thickness t1=10 mmInternal…

Q: 8. What surface texture (in microinches) is specified for the cylindrical surface with a maximum…

A: As per Bartleby Answering Guidelines we are supposed to give answer for first three sub parts of the…

Q: A vertical plate is submerged in water. Find an integral expression that can be evaluated to deter-…

A: The vertical plate is immersed in water

Q: Section Problem 2 Sketch the indicated sectional views in the space provided. 7 S

A: Given: Sketch the indicated sectional view.

Q: 8 ft 13.68 kips 24 ft 1.32 k/ft

A:

Q: 5.102 For the machine element shown, locate the x coordinate of the center of gravity.

A:

Q: Suppose a 3x3 matrix A admits a factorization as A=PDP-1 where P is some invertible matrix and D is…

A: GivenA is a matrix of 3×3factorization of A as-A=PDP-1whereP is some invertible matrixD is diagonal…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A: Given:Elevation difference between the lake and the reservoir, ∆z=25 mWater flow rate, Q=25…

Q: ● . At a point on the surface of a component a 60° strain gauge rosette measures & = 0.00046…

A:

Q: 5. If the radius of each notch on the pictured bending plate is r = 10 mm, determine the largest…

A:

Q: 8. The two bars below are each 20 kg, with length 1.5 m. They're connected by a pin joint at their…

A: To find: The acceleration of the right pin. Given: The force at pin is F=500 N. The mass of rod is…

Q: Water from a reservoir is pumped over a hill through a pipe 900 mm in diameter and a pressure of one…

A: Given:Pipe diameter, d=900 mm=0.9 mPressure at the pipe discharge, P2=1 kg/cm2=1*98.1 kPa=98.1…

Q: Calculate the electricity energy required in units of D for desalinating 150 w of water and it takes…

A: The amount of waterV=150 l=0.15 m3 The electricity for per unit of water 3.70 kWhm3

Q: Explain briefly the importance of draft pressure during boiler operation.

A: Draft pressure in a boiler refers to the difference in pressure between the combustion chamber and…

Q: Show that if the atmosphere is isothermal, the temperature change of a parcel of air rising…

A:

Q: 2. The overhang beam is subjected to the uniform distributed load having an intensity of w = 50 kN/m…

A:

Q: A GPP (Gas Power Plant) uses a simple Brayton cycle. Air enters the compressor at pressure, P = 1…

A:

Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

A:

Q: 4) A slider crank mechanism is shown in the figure. Crank OA rotates anticlockwise at 100 rad/sec.…

A:

Q: *9-76. The thin-walled pipe has an inner diameter of 2 in. and a thickness of 0.1 in. If it is…

A:

Q: A VA= 18 m/s A=32 t B Vc = ? ac = ? VB = 125 a6 = 0.552₂2 1. For the arrangement of cable and…

A:

Q: A gas is heated in a rigid container of volume V. Derive expressions to evaluate how U and H vary…

A: A gas is heated in a rigid container of volume V.

Q: Part A Y FR = Submit Part B In (Figure 1), ₁ = 2.5 kN/m and w2 = 7.5 kN/m Replace the distributed…

A:

Q: The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of…

A:

Q: Section Problem 2 Sketch the indicated sectional views in the space provided.

A: Given: Sketch the indicated sectional view in the space provided.

Q: A beam 3m long has a weight of 200N at one end and another weight of 80N at the other end. The…

A: To solve this problem, we can set up the appropriate force system and then use the principle of…

Q: A 76 mm solid shaft is to be replaced with a hollow shaft of equal torsional strength. Find the…

A:

Q: Determine the binding reactions

A: F1=3 kNF2=0 kNF3=5 kNM=2.5 kNma1=3 ma2=1 ma3=2 ma4=1.5 ma5=2.5 α=60°

Q: 4. The sign is subjected to the uniform wind loading. Determine the stress components on the…

A: To Find : The stress at point A B, C and D. Given : The pressure is P=10.5 kPa The projection area…

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: A solid stainless steel [G = 12,500 ksi] shaft that is 30 in. long will be subjected to a pure…

A:

Q: A 1 ft-diameter PVC pipe (CHW= 150) is conveying 13.4 ft/sec. the friction head loss over a 100 ft…

A: The diameter of the PVC pipe, d = 1 ft The flow rate, Q = 13.4 ft3/s The length, L = 100 ft

Q: Learning Goal: To be able to find the center of gravity, the center of mass, and the centroid of a…

A:

Q: A 6-m long x 50-mm-diameter rod of aluminum alloy [E = 70 GPa, v = 0.346, and a = 22.5 x 10-6/°C] is…

A: Given: Length, L = 6 m or 6000 mm Diameter, d = 50 mm E = 70 GPa or 70,000 MPa v = 0.346 α=…

Q: A 1-inch round steel shaft transmits 6 hp and rotates 200 rpm. If this shaft is subjected to pure…

A: Given

Q: The slotted arm OA rotates about a horizontal axis through point O. The 0.21-kg slider P moves with…

A:

Q: A solid 1.08-in.-diameter steel [G= 9500 ksi] shaft is subjected to the torques shown. Determine the…

A:

Q: The stress in thin-walled sphere is greater than the thin-walled cylinder. (A) True (B) False

A: □ The following types of stresses are generated in case of the thin-walled pressure vessel: ▪︎…

Q: A stress of $=(0,-2,1) MPa acts on a plane whose normal î lies in the same direction as the vector…

A: Given Data: S→ = 0,-2,1 MPa=0i^-2j^+k^N→=(10,3,-8)=10i^+3j^-8k^ Find: Magnitude of shear Stress on…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.