a. For the circuit shown below, load resistance is 180 ohm, determine load voltage, the resistance Voltage, the zener current and the zener power dessipation. b. Repeat part (a) with R load resistance of 330 ohm c. and with load resistance of 660 ohms d. also with a 1 kilo-ohm load resistance In each value of load resistance, is the zaener diode safe?

a. For the circuit shown below, load resistance is 180 ohm, determine load voltage, the resistance Voltage, the zener current and the zener power dessipation. b. Repeat part (a) with R load resistance of 330 ohm c. and with load resistance of 660 ohms d. also with a 1 kilo-ohm load resistance In each value of load resistance, is the zaener diode safe?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____ b. What is the minimum number of small-appliance circuits permitted by the Code? _____ c. How many small-appliance circuits are included in this residence? ____
Explain the difference between cumulative- and differential-compounded connections.
Can you explain in detail on how to solve this?Determine current ID graphically using load line analysis, if Zener voltage is 3V.
Describe the state estimation process in power systems. How does it use measurements from various sensors to estimate the current state of the network and detect any anomalies or errors?
Explain, in your own words with the aid of the graph the Load Line Analysis concept. The student should illustrate the following points on the graph: ICsat VCEcutoff Different IBQ values Load Line Q-Point
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
Find the value of the load resistance for the maximum power tranfer theorem.
For the circuit Shown below draw the DC-load line and determine the value of R2 so that the Q-Point located at the current of DC-load line assume β=100
Use a load-line analysis of the circuit shown in the figure below to determine the valuesof VDSQ, VDSmin, and VDSmax. The characteristics of the FET are shown in the plot onthe right. Note that the labelled IDQ is for a different textbook example, not for thisproblem. Hint: First, replace the 15 V source and the resistances by their Theveninequivalent circuit.
Subject : ELECTRONIC CIRCUIT ANALYSIS AND DEVICES Please give the DC ANALYSIS circuit and AC EQUIVALENT CIRCUIT of this problem before proceeding to find letters a, and b. (Note : Neglect Vbe)
A load resistor RL is in parallel with a noisy source (vS << VS), and a biasing component, which canbe a linear or a nonlinear element. Suppose we can write the total source voltage vS and the totalload voltage vL as shown in the image. Answer the ff and explain clearly. i. Let the biasing component be a linear resistor with resistance RB. Without the noise, determinethe value of RB so that the load voltage is 5V. ii. With the noise, determine the ratio of the load voltage noise and the source noise (vI /vS )..
For a switching regulator with a square wave output, the DC levels is given by the formula . Where Vdc is the output, Vmax is 12V, Vdrop is the saturation drop (on) of our switching device which is 0.7V, T is the period and Ton is the time Vmax is on for a period. Find the duty cycle in % needed for Vdc 10V and 5V. Find the efficiency for 10V and 5V output operation using Powerout/(powerout+powerloss)