A1/ For the shape below, the Resultant of three forces (200N, F1 and F2) is 600N: (a) the force F1 is: * 600 N F1 4 12 200 N 30 F2 A1/(b) the force F2 is: wer A1/(c) The direction of resultant *

Q: One end of a solid cylindrical copper rod 0.2500 m long and 0.0350 m in radius is inserted inta a la...

A:

Q: A water tube boiler has the following data: Percent rating Heating surface Heating value of coal use...

A: Given DataPercentage rating=200%A=250m2Heating value of coal used=27446.8kJ/kgFactor of evaporation=...

Q: Find the Normal Stress at points A, B, and C

A: To Find the Normal Stress at points A, B, and C 

Q: At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The temp...

A: m˙=.2 lb/secP1=14 psiaT1=130° FMaximum temperature T3=4500°R or T3=4040.330°FCompression ration r=v1...

Q: A Simple Aanhine cyele works betuween pressures 56 par and loeo kpa, the initial eondifion of steam ...

A: given; find efficienecy=?work ratio=?specific steam consumption=?  

Q: Consider the simply supported truss as defined in the figure and parameter table. Find the force in ...

A:

Q: A thin rectangular plate is uniformly deformed as shown. Determine the total shear strain

A:

Q: . Determine the velocity of the

A: NEED TO DETERMINE THE VELOCITY OF STEAM AT THE NOZZLE EXIT.

Q: The strut AB of negligible mass is hinged to  the horizontal surface at A and to the uniform 24- kg ...

A: Given Mass = 24 kg Friction coefficient = 0.4 To find Magnitude of couple M

Q: A 30-kW motor drives a fan and delivers air through a duct 1.0 m x 1.0 m at 11.684 cm WG static pres...

A: Given Dataρair=1.2kg/m3ρwater=1000kg/m3P=30kW11.68cm WG=1.15kPa2.159cm WG=0.651m/s

Q: Use rotation about the current frame to calculate the transformation matrix for a rotation of 90° ab...

A: The first transformation matrix for rotation of 90° about y0 axis  Ryθ=cosθ0sinθ010-sinθ0cosθRyθ=cos...

Q: In an oscillating incompressible flow field the force per unit mass acting on a fluid particle is ob...

A:

Q: I NEED A SIMILAR PROBLEM JUST LIKE THIS IN THE PICTURE BELOW AND ALSO NEED THE ANSWER TO A SIMILAR P...

A: Given Load in the concurrent plane To findResultant of A Angle of resultant A Resultant B

Q: A Francis turbine is installed with a vertical draft tube. The top of the draft is 1.0 m below the c...

A: Given Data The head of the water elevation is: Hw=50 m The height of the water level is: HT=3 m The...

Q: A motorcyclist left from his work at 5:45 in the morning and arrived at the coffee shop 42 km away a...

A:

Q: Explain briefly Pressure-spring thermometer

A:

Q: A rectangular steel bar supports the two overhanging loads shown in the figure. Using superposition,...

A: Given DataF=500Nb=9mma=250mml=500mmh=35mm

Q: A 13 m simply supported beam with a uniform load of 3 kN/m from right end to the left end and has  a...

A: Given data: L=13 mw=3 kN/mEI=11000 kN.m2 Need to determine the maximum deflection.

Q: What does % elongation measures of?

A: Elongation: The increase in length of any object is known as elongation. The length of the object in...

Q: Consider a river flowing toward a lake at an average velocity of 3 m/s at a rate of 500 m³ls at a lo...

A:

Q: 5.13 A hydrometer is a device for indicating the specific gravity of liquids. Figure 5.21 shows the ...

A:

Q: T F A В

A:

Q: 2 kg of air at 500 kPa, 80°C expands isentropically in a non-flow system until its volume doubles, t...

A: Mass of air m=2 kgT1=80°C+273=353 KP1=500 kPav1=vExpands isentropically and final volume v2=2v1Ambie...

Q: ᴄᴀʟᴄᴜʟᴀᴛᴇ ᴛʜᴇ ᴘᴏᴡᴇʀ ᴅᴇʟɪᴠᴇʀᴇᴅ ʙʏ ᴛʜᴇ ᴘᴜᴍᴘ (ᴡᴘ) ᴛᴏ ᴛʜᴇ ᴡᴀᴛᴇʀ ᴀɴᴅ ᴇꜰꜰɪᴄᴇɪɴᴄʏ ɪꜰ ᴛʜᴇ ᴛʜᴇ ᴍᴏᴛᴏʀ ᴘᴏᴡᴇʀ (ʙ...

A:

Q: Part A A shaft is made of an aluminum alloy having an allowable shear stress of Tallow = 104 MPa. (F...

A: As per given  Allowable stress=104mpa Shaft diameter =115mm We have to determine maximum torque T to...

Q: Consider the simply supported truss as defined in the figure and parameter table. Find the force in ...

A:

Q: A1/ For the shape below, the Resultant of three forces (200N, F1 :and F2) is 60ON: (a) the force F1 ...

A:

Q: Please elaborate the following: Typical stress-strain characteristics of steel in simple tension and...

A: Characteristics of Stress Strain  Mechanical Properties

Q: A1/ For the shape below, the Resultant of three forces (200N, F1 and F2) is :600N: Determine : 1- fo...

A:

Q: Sthe moment about point A i: 300 cm A 200 N 450

A:

Q: a b A B Figure P-319 and P-320

A: The calculated maximum torque that can be applied.

Q: Produce the Front, top and Side VIEWS of the drawing shown below using appropriate scale and dimensi...

A: Given 3D model To find Front view Top view Side view

Q: How long does it take to go from A to C? Express your answer to three significant figures and includ...

A:

Q: 3) Figure - 2 shows a round bar (Ø 40 mm) being used as a bracket to support equipment attached as s...

A: Find the stress and strain in each bar. And total elongation

Q: C3/(a) For the figure below take M number of you and find the reactions ? 3 m 3m 3 m E C 12 13 : 5 1...

A:

Q: 4-6.6. For the structure loaded as shown in. Fig. P-4-6.6, find the horizontal and vertical componen...

A: Given data  Given force system.

Q: The cleararce between a 75 mm diameter shaft and its journal bearing is 0.8 mm. The speed is 120 rpm...

A:

Q: 3 A fluid enters with a steady flow of 3.7 kg/s and an initial pressure of 690 kPa, an initial densi...

A:

Q: A ½ in 13 UNC x 12 m long steel bolt mist carry an impact load of 40 in.Ib. Calculate the stress are...

A: Given Data The nominal size of the thread is: 12 in The type of thread is: UNCCoarse thread series ...

Q: discharges it at 100 kPa and 200°C (h = 2875.45 kJ/kg). The inlet velocity is negligible, and the he...

A:

Q: Steam at 6.3 kg/s enters a turbine with h = 3263 kJ /kg, and leaves with h = 2232 kJ /kg. For a heat...

A:

Q: The gauge pressure in a steam boiler is 30 bar, the rarefaction in the condenser as  indicated by a ...

A: Gauge pressure in a steam boiler Pbgauge=30 bar  since 1 bar =105 N/m2 or 100 kN/m2 so,Pbgauge=30×10...

Q: The velocity of a particle which moves along the s-axis is given by v = 2 – 5t + 5t7, where t is in ...

A:

Q: An ideal gas is enclosed in cylinder with frictionless piston at 300 K and 2 bar. The gas expands fr...

A:

Q: A pump recieves 5.6kg/s of hydraulic oil (SG=.85) at 2.5kg/cm2 and discharges it at 13kg/cm2. What i...

A: Solution is attached below: 

Q: 4. A pump recieves 5.6kg/s of hydraulic oil (SG=.85) at 2.5kg/cm2 and discharges it at 13kg/cm2. Wha...

A:

Q: A 1000N block was pushed by a force P of 1500N up an incline upward to the right at a slope of 3 ver...

A: Calculated the required work to increase the velocity of the block from 3 to 15 m/s.

Q: A) Determine its velocity at time t. B) What is its position when t = 4 s?

A: Need to determine velocity and position.

Q: A 7.5 ft- 15 ft Smooth wall 9 ft

A:

Q: Find maximum principal stress 70 MPa 50 MPa - 40 MPa - – a, =-40 MPa o, - 70 MPa ,--50 MPa

A: Given, Normal stress in x direction = σx = -40 MPa Normal stress in x direction = σy = 70 MPa Shear ...

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.