AB and CD rod rod are of the same sectional alloy and have the same A modulus of elasticity. The system is fixed at points A, C and E with a hinge connection. Find the value of the displacement (8) at point F with respect to the given. A = 301 (Cross-Sectional Area), E = 90871 B (Modulus of Elasticity), P = 18741 (Strength), x = 241, L1 = 151, L2 = o 247 and L3 = 90. X FE %3D %3D L2 L3

AB and CD rod rod are of the same sectional alloy and have the same A modulus of elasticity. The system is fixed at points A, C and E with a hinge connection. Find the value of the displacement (8) at point F with respect to the given. A = 301 (Cross-Sectional Area), E = 90871 B (Modulus of Elasticity), P = 18741 (Strength), x = 241, L1 = 151, L2 = o 247 and L3 = 90. X FE %3D %3D L2 L3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.23P: Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the...

See similar textbooks

Similar questions

A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
If an isotropic material has a shear modulus of 21 Gpa and a Poisson’s ratio of 0.4, calculate its Young’s modulus. Select one: E = 59 Gpa E = 300 Gpa E = 30 Gpa E = 80 Gpa E = 450 Gpa
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
steel cab AB has a cross sectional area of 400 mm^2, modulus of elasticity=200 GPa, and a Length of 2.5m. post BC has a cross sectional area of 200mm^2, modulus of elasticity = 50 GPa., and a calculated length. find horizontal and vertical movement of point B
The rigid bar ABC is supported by pin at A and aluminum wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35KN. Where E of aluminum equals 70GPA and the area of the wire is 200mm^2 -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Suppose that the following rod system is subjected to a specific amount of load that makes the displacements of nodes 2 and 3 to be q2=2.18 mm and q3=0.32 mm. The system is made of a material with Young's modulus of E=150 GPa. Suppose that the vector B (strain-displacement vector) for node 1 is B 1 = 14.9 × [ - 1 . 5 2 - 0 . 5 ] 1/m. Workout the stress of node 1 in GPa. a
The bulk modulus of the steel bar with modulus of elasticity 1.8x105N/mm2 and Poisson’s ratio 0.25 is
A slightly tapered bar AB of solid circularcross section and length L is supported at end B andsubjected to a tensile load P at the free end A. Thediameters of the bar at ends A and B are dA and dB,respectively. Determine the length of the bar if theelongation of the bar due to the load P = 45 kipsis 0.02 in. Assume that E = 10,400 ksi.
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is subjected to tension within the elastic region. Determine the force ( in N) that will produce a reduction of 0.003 mm in the diameter.