Activity 4: For the low-pass active filter shown below, the transfer function is expressed as: Vo V ZR + Zc where: 106 ZR = 2000 , Zc: jw rad. w = angular frequency in | ZR Vo Vi o ww 4-A) Show that the can be written as: V. V- 500 + jw 500 4-B) What should be the value of w so that the magnitude of 4 is ?

Activity 4: For the low-pass active filter shown below, the transfer function is expressed as: Vo V ZR + Zc where: 106 ZR = 2000 , Zc: jw rad. w = angular frequency in | ZR Vo Vi o ww 4-A) Show that the can be written as: V. V- 500 + jw 500 4-B) What should be the value of w so that the magnitude of 4 is ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the Vout/Vin versus frequency characteristics of an LC Bandpass filter. Show flc and fhc on the sketch and explain how they are defined. On this sketch, show the bandwidth (BW) of the filter and explain how it is defined.
Given the following: VCC = 15V C1= 1uFhfe =150 hie = 1.08 kΩR1 = 100kΩ C2 = 220uFR2 = 20 kΩ C3 = 0.32 uFRC = 2 kΩ Cwi = 12pF,Cwo = 10pF RE = 500 Ω Cbe = 15 pF Cbc = 25pFRL = 2 kΩ Determine the following: Midband gain Av Midband Total Voltage Gain AvT Midband Total Current Gain AiT
1. a) Show (via a qualitative analysis) that the circuit is a bandreject filter. 2. b) Support the qualitative analysis of (a) by finding the voltage transfer function of the filter. 3. c) Derive the expression for the center frequency of the filter. 4. d) Derive the expressions for the cutoff frequencies ωc1 and ωc2. 5. e) What is the expression for the bandwidth of the filter? 6. f) What is the expression for the quality factor of the circuit?
A) Write the equation for the small-signal gain function ???????for the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system.
Tuned Circuit Design Using a VARICAP (a) Refer to the capacitance curves for the Motorola 1N4002 The input tuning circuit of a standard analog FM radio is given below. Specify, that is design for, a voltage, capacitance, and inductance required to tune the circuit to the center frequency of KUMD-FM which operates at 103.3 MHz. Sketching and labeling a representative resonance curve is required to support your calculations. There is no single correct design answer set of values since it depends upon the voltage you initially select to tune your diode.
Let R = 150 Ohm and C = 1uF. What is the peak gain offered by this filter? At what frequency does the frequency response achieve this gain? What is the lower cutoff frequency? What is the upper cutoff frequency? What is the passband width?
For the given circuit, derive the transfer function vo/vi and show how to determine the location of the pole and zero frequencies.
Compute the transfer function of the given signal flow graph below:
For a mosfet amplifier circuit, how can I choose an input and output capacitor with poles at 10Hz and 100Hz? Where RC = 1/w.
What is a bandpass filter? How is its bandwidth defined?
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 42.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit.NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
Sketch the Nyquist Diagram and the Bode Plot of the transfer function