An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 3 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 400 mm P = 2 kN 200 mm

An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 3 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 400 mm P = 2 kN 200 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

The thin-walled tube is subjected to an axial force of 40kN. If the tube elongates 4mm and its circumference decreases 0.09 mm, determine the modulus of elasticity, Poisson's ratio, and the shear modulus of the tubers material. The material behaves elastically.
The two sheets of soft plastic are bonded to the central steel strip. Determinethe magnitude of the largest force P that can be safely applied to the steel strip andthe corresponding displacement of the strip. For the plastic, use tw = 10 ksi and G = 800 ksi. Neglect deformation of the steel strip.
A 100- m steel tape is used to measure the distance of the line and found to be 1,539.28m long. During measurement, the tape is supported the ends under a pull of 10kg and the observed mean temperature is 31°C. The tape is of standard temperature of 20°C and a tension of 12kg. The cross sectional area of the tape is 0.035 sq. cm. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 x 106 kg/ sq. cm. The tape weighs 1.5kg. a. Determine the total correction for temperature. b. Determine the total correction due to sag. c. What is the correct length of the line?
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
Note: Give me right solution according to the question. If any data missing assume that. A wheel applies 40 kN load on a semi-infinite elastic space as shown in Figure. The modulus of elasticity of the material is 150 MPa and the Poisson’s ratio is 0.38. Assume the load is applied on the surface as a concentrated force. The vertical deformation at a depth of 500 mm at the centerline of the wheel is most nearly: 0.64 mm 0.07 mm 0.41 mm 0.26 mm
A cube of side 50 mm is subjected to a pressure of 80 MPa in a pressure chamber. Determine the change in the length of cube if it has a modulus of elasticity of 200 GPa and Poisson's ratio of 0.3.
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
A 50 m diameter solid metal bar is subjected to a compressive load of 178 kN. Transverse and longitudinal changes are measuredd with the use of an electroninc strain gages and the strains are determined to be 0.0012 longitudinally and 0.0004 transversely. Compute the Modulus of Elasticity (MPa).
Integrate to get the axial deformation formula
#1 Determine the deformation of point b in mm
Determine the threshold torsion