An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an a three-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) line current and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated in the line quantities of the alternator.

An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an a three-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) line current and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated in the line quantities of the alternator.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.52P: A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated...

See similar textbooks

Similar questions

With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
Three-phase alternator supplying a three wires, CBA system with a line voltage of 100 Volt, connected to a three impedances of 3 - j 4 in Delta connection. Determine the line current, phase current, phase and line voltage and draw the voltage-current phasor diagram, assuming that VBC is the reference vector.
In the above figure, a single line model of a three-phase power system is given. Base power 50MVA, base voltage 13.8kV according to its value, a) Per-unit values of power system circuit elements according to the given base power and base voltage values. calculate. b) The perunit you calculate by drawing the equivalent impedance circuit for one phase of the power system given in the figure. show on the values.
Please provide Handwritten answer. Can three single-phase transformers be connected in Y-Y with substractive polarity, in such a way that the line to line voltage be 30 degrees lagging with the secondary line to line voltages?
Subject - Design electrical circuits for single phase AC networks Question - Analyse the methods that improve the power factor of a electrical circuit.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
A three-phase, 3-wires CBA System alternator, sending 3-phase voltages of 339.4 volt to the lines, having a delta connected load, with VCA is the reference vector. ZBC = 12.99 – j7.5 ZCA = 8.66 + j5 ZAB = 10 + j0 Determine the phase and line current b) draw the phasor diagram and c) true power generates by the generator neglect the line losses.
The IAC current of a balanced three-phase delta connected load is known as 10 Amps (-10 degrees) and the VAB voltage as 20 Volts (10 degrees). Accordingly, calculate the following expressions by considering the positive phase sequence. A) IAB=? B)load impedance=? C)IBC=?
A balanced three phase inductive load is measured by a single wattmeter using the current transformer method which has a reading of 100 watts. For the same load, it is measured again, using potential lead shift method wherein the wattmeter is placed at line 2. If the wattmeter reading across lines 1 and 2 is -1,200 watts, voltage across lines 3 and 2 is 200 bar angle 60 degrees, and the current at line 2 is 75 amperes, calculate the power factor. Assume voltage across lines 1 and 2 as reference voltage.
An AC three phase distribution system (given in Figure 2), which has end user with balanced three phase (10A) load, is given in the figure. The phase-neutral voltages of the transformers are given as V1=224V, V2=225V, V3=228V and V4=231V respectively. a) Calculate phase-neutral voltage of the bus-bar (B). b) Calculate currents of the transformers (I1, I2, I3 and I4) c) Calculate phase-neutral voltage of the point K while the output of TR3 and TR4 (xy) have been short circuited for a transient time (transformers are still operational) by the line fault.