An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rodis subjected to atensile load of SkN. Assume that the material is in the clastic regionand E 69 GPa. If Poisson's Ratio is 0,38, what will be the lateral strain?V -flateral)rtaxial)

Answered: Image /qna-images/answer/2e696724-822c-4f05-965b-d55aaf8b6d0a.jpg

An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E 69 GPa. If Poisson's Ratio is 0.38, what will be the lateral strain? E-ot VE(lateral)rtaxial)

An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E 69 GPa. If Poisson's Ratio is 0.38, what will be the lateral strain? E-ot VE(lateral)rtaxial)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Related questions

Q: How do you think you could use what you will learn and the results you will get from the topics in C...

A: A very important topic of civil engineering i.e. Treatment of waste water and treatment of sewage A...

Q: 10 15' 14' 12' 20 F E 14' 55°

A: Calculate the reaction at the support , ∑Fx=0-Ax+Fx=0Ax=Fx ...

Q: DEPARTURE LATITUDE AZIMUYH FROM NORTH COURSE LENGTH +E - W +N -S 5.53 0°50' 296°06' 205 54' 135 20' ...

Q: m wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-...

A: Given:- b=250mm d=500mm 4-20mmdiameter bar at bottom 2-16mm bard at top Concrete cover to bar centro...

Q: Question 41 A symmetric I-shaped built up steel beam is composed of 200 mm x 14 mm flange plates at ...

Q: A symmetric I-shaped built up steel beam is composed of 180 mm x 12 mm flange plates at top and bott...

Q: Make a flowchart showing the procedure on design of structural steel beams with doubly-symmetric hot...

A: We have to draw a flow chart for showing the procedure on design of structural steel beams with doub...

Q: A solid sphere made of aluminum (SG suspended in water by a cable. 2.7) is The cable has a tension o...

Q: Problem: The beam has a given cross section as shown. fc = 9.8 MPa, fs = 138 MPa, n = Determine the ...

A: Given: Characteristic strength of concrete fc = 9.8 Mpa Characteristic strength of steel fst = 138 ...

Q: Calculate the annual monetary benefit ($ from travel time/delay savings) for an intersection improve...

Q: The kinetic energy of a 4.0 kg object moving at 3.0 m/s is: 1. 12 J *2. 18 J 3. 36 J 4. 48 J

A: use formula of kinetic energy.

Q: The following data pertaih to a sandstone formation((a 0.81, m 2): formation thickness -15 ft; forma...

A: Given, Formation thickness =15 ft Formation water salinity= 140000 ppm Formation temperature =180°F ...

Q: 2/34 A portion of a mechar K lows: Pennies and dimes roll down the 20 incline the last triangular po...

A: The given data is as follows: Inclination=20∘Mass of dimes=2.28 gmMass of pennies=3.06 gmSlant dista...

Q: A W12x79 of AS73 Grade 60 (Fy - 415 MPa) steel is used as a compression member. It is 7.7 m long, fi...

A: A=14500mm2

Q: A compound shaft drives three gears, as shown in Figure P6.14. Segments (1) and (2) of the compound ...

Q: D 9AN

Q: Question 35 A simply supported beam 300 mm wide, 500 mm deep and spans 5.9 m supports a service supe...

Q: A wide flange section has the following properties: bf = 240 mm tf = 14 mm d = 300 mm tw = 8 ...

Q: Situation 1] A circular road is proposed to be laid out with tangent AB whose bearing is N81°54'E in...

Q: A PL 3/8 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy= 36ksi, Fu = ...

Q: A simple circular horizontal curve has a radius of 5200 ft and an intersection angle 35°. The statio...

Q: Using the moment-area theorems and E = 29(103) ksi, I = 500 in4 A. Reactions at A B. Determine the m...

Q: An axially loaded tied column must sustain the following service loads: - 1,000 kN - 1,600 kN Total ...

Q: A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of ...

Q: 10 KN 20 KN / m 5 KN / m SIMPLE STRESSES A 5 KN / m 50 KN-m 5 KN / m F E 2. Points C and D of the 1....

A: Wooden column=500mmx600mm

Q: A simply supported beam 300 mm wide, 500 mm deep and spans 5.4 m supports a service super imposed de...

A: This question is related to the Structure of concrete structure. In this question using stress strai...

Q: 10 KN 20 KN / m 5 KN / m A В SIMPLE STRESSES 5 KN / m D 50 KN-m 5 KN / m F E 3. Points C and D of th...

Q: Compute the Ig of a rectangular cross section of a beam with a base of 200mm and a height of 350mm.

A: Using formula

Q: 2 k/ft A B C D 18 ft 15 ft – 18 ft Figure 3

Q: A three-plot irrigation area has a slope of 0.5:2 (V: H) receives 198m3 of water diverted from the s...

A: Given Data: The volume of water diverted from the source is 198 m3. The crop factor is 5. The pan ev...

Q: A beam of rectangular cross-section is subjected to a vertical shear force 'V. The shear force carri...

Q: A solid circular bar is acted upon by tensile force of 20N. The diameter of circular Bar is 10 mm. T...

A: Given data : The original length of bar (L)=10 m The change in length of bar (L')=0.2 m The value of...

Q: s used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm, ...

A: Given:- Ag = 1,852 mm2 t = 8 mm s = 50 mm, 22 mm diameter bolts To find:- Design strength (kN)

Q: The beam ABC shown in given figure is horizontal. The distance to the point of contraflexure from th...

A: Given data, The distance to the point of contra flexure from the fixed end A

Q: The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Usi...

Q: Determine if w12x14 (A36) section is Compact, Non-Compact or slender. Show neat handwriting and comp...

A: The given data is shown below: W12×14A36 steel

Q: A 500-mm-diameter, non-slender, spiral column is symmetrically reinforced with six 25 mm vertical ba...

Q: Situation 2] A simple curve having a radius of 231.0 m has tangents of N28.8°E and N66.0°E. A line r...

Q: Design a braced square column including its dimension (between 12 to 20 inches), reinforcement, cove...

Q: the given section of beam is at point of maximum moment of the beam loaded shown. use n=8 , calculat...

Q: A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every t...

Q: 300 kN 50 kNm 6.0 m 3.0 m El is constant

Q: A symmetric I-shaped built up steel beam is composed of 160 mm x 9 mm flange plates at top and botto...

Q: gth (kN) of 4-legged stirrups 10-mm-diameter, spaced at 200 mm on centers for a beam with effective ...

A: Given:- 4-legged stirrups 10-mm-diameter, spaced at 200 mm on centers for a beam effective depth of ...

Q: Question 5 A square footing 2 m x 0.36 m thick supports a 300 mm square column at its center. Column...

Q: the maximum steel ratio if the beam is singly reinforced in negative bending with the given material...

Q: Determine the tensile steel strain

Q: According to the provisions of NSCP 2015, in flexural reinforced concrete members a compression cont...

Q: Given the laboratory results of the Atterberg Limit Test, plot the water content versus the number o...

Q: beari ngs ес

A: SURVEYING:

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod
is subjected to atensile load of SkN. Assume that the material is in the clastic region
and E 69 GPa. If Poisson's Ratio is 0,38, what will be the lateral strain?
V -flateral)rtaxial)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.1 The state of plane stress shown in figure is expected to occur in an aluminum casting. Knowing that for the aluminum alloy used σUT = 80 MPa and σUC = 200 MPa, determine whether rupture of the casting will occur. a) Using Mohr’s criterion b) Using Tresca’s yield criterion
At an axial load of 24 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 3.1 mm while the bar width contracts 0.23 mm. The bar is 210 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= GPa mm
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 185 mm, a wall thickness of 5 mm, and a length of 5.0 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 39°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
A steel wire with a diameter of d = 1/16” is bent around a cylindrical drum with a radius ofR = 36”.(a) Determine the maximum normal strain in the wire.(b) What is the minimum acceptable radius of the drum if the maximum normal strain mustremain below yield? Consider an elastic modulus of 30000 ksi and yield stress of 100ksi.(c) If R = 36”, what is the maximum acceptable diameter of the wire if the maximum normalstrain must remain below yield?
At an axial load of 22 kN, a 45-mm-wide by 15-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.25 mm. The bar is 190 mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness
A critical point in a part made of a ductile material is subject to the following state of plane stress: 15ksi, 30 ksi, 15 ksi, Ox,min = -35 ksi, Oy,min = 30 ksi, Txy,min = -15 ksi. Ох,max бу,max Тxy,max %3D There are no stress concentrations. The load line is propositional. The material has a yield strength of Sy = 130 ksi, an ultimate strength of Su = 200 ksi, and a fully corrected endurance limit of Sn : 75 ksi. Calculate the: (a) Static factor of safety using the MSSTF, (b) Static factor of safety using the DETF, (c) Fatigue factor of safety using the Soderberg criterion, (d) Fatigue factor of safety using the Goodman criterion, (e) Fatigue factor of safety using the ASME elliptic criterion.
At an axial load of 25 kN, a 50-mm-wide by 15-mm-thick polyimide polymer bar elongates 3.1 mm while the bar width contracts 0.26 mm. The bar is 220 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E- (b) v- (c) Audness GPa mm
At an axial load of 22 kN, a 15-mm-thick x 35-mm-wide polyimide polymer bar elongates 4.2 mm while the bar width contracts 0.25 mm. The bar is 215-mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine Poisson's ratio. O 0.366 O 0.336 EBA O 0.473 O 0.229 O 0.427
Q.3. (30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
At an axial load of 22 kN, a 15-mm-thick × 50-mm-wide polyimide polymer bar elongates 5.7 mm while the bar width contracts 0.15 mm. The bar is 245-mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine Poisson’s ratio.
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 14 mm, and a length of 5.1 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 44°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) õ = i mm AD = i mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm