An eccentric load of 66 kN is acting as shown in the figure 6.5. Using elastic method, compute for the maximum force on the most stressed rivet. 2 Using the reduced eccentricity method, compute for the maximum force on the most stressed rivet Using ultimate strength method, compute for the max. force on the most stressed rivet. 100 100 e-200 900 75:75 Figure 6.5 P-66 KN

An eccentric load of 66 kN is acting as shown in the figure 6.5. Using elastic method, compute for the maximum force on the most stressed rivet. 2 Using the reduced eccentricity method, compute for the maximum force on the most stressed rivet Using ultimate strength method, compute for the max. force on the most stressed rivet. 100 100 e-200 900 75:75 Figure 6.5 P-66 KN

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

The wide flange beam shown supports the concentrated load ? and a total uniformly distributed load of 2?. Determine the maximum safe value of ?i f flexural stress ?? ≤ 10 ??? in tension, ?? ≤ 20 ??? in compression and shear stress ? ≤ 1.4 ???.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
The simple beam carries a concentrated load P = 15kN. Dimension a and b are 2.5m and 1.2m. respectively. What is the required section modulus of the beam, in mm^3, if the stress is 120Mpa?
Find shear force value under point load 10 Kn
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of692.5. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads of31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
A simply supported beam 4 m long is carrying a variable load of w = 0 KN/m at the left support and w = 15 KN/m at the right. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual shearing stress of the beam in MPa?
A cast iron beam 12m long and supported as shown carries a uniformly distributed load of intensity wo, N/m, (including its own weight). The allowable stresses are ??? ≤ 25 MPa and ??? ≤ 90 MPa. Determine the maximum safe value of wo, in N/m, if x= 1.2m.
A pre stressed concrete simple beam having a cross section of300mmx600mm is subjected to a pre stressing force in steel whicheventually reduce to 1200KN due to losses acting on a parabolic tendons.The beam carries a total uniform distributed load of 20 KN/m includingbeam’s weight. Using three methods calculate the total stresses at midspan section of the beam. Given:B = 300mmD = 600mmP = 1200KNW = 20 KN/mE @ mid span = 50 mmE @ end section = 0 mmL = 10 mm Det. the total stresses of the extreme bottom fiber at midspan using load balancing method. (Mpa)
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
A rectangular beam of length 702mm has a width of 132mm and a depth of301mm. Compression steel bars are placed at a distance 98 mm from the extreme concrete compressivefiber. The beam supports service dead loads of dead load (16 KN/m) and live load (24 KN/m). Reinforced with 4 25mm tension steel bars and 4 12mm tension steel bars f′c = 42 MPafy = 519 MPa 1. Solve for the height of the neutral axis measured from the extreme compression fiber.2. Solve for the design moment.3. Solve for the strength reduction factor.
A prestressed beam of a certain condominium was designed to have a rectangular section 300mm x 600mm deepand has a simple span of 9m. At the midspan section, the tendons are placed at 200mm above the soffit whichcarries an initial prestressing force of 1,110KN which ultimately relaxes to 880 KN. If the allowable stress inconcrete in compression is 13.5 MPa and in tension is 1.4MPa, determine the safe moment it could carry and thesuperimposed live load that it could also carry. Assume concrete will not crack in tension.