An elastic rod with a cross-sectional area A = 2mm2 is stretched from an intial legth of 1.0m to a final legth of 1.1m at a constant tempreture of 15 degrees celcius . Calculate the heat exchanged between the elastic rod and its surroundings if it is made of a material with a isothermal Youngs modulus ET = 150GPa and a linear expansivity at constant tension af = 15 x 10 -6 K-1. a) 129.6675 J b) -129.6675 J c) -6.75 J d) 6.75 J

An elastic rod with a cross-sectional area A = 2mm2 is stretched from an intial legth of 1.0m to a final legth of 1.1m at a constant tempreture of 15 degrees celcius . Calculate the heat exchanged between the elastic rod and its surroundings if it is made of a material with a isothermal Youngs modulus ET = 150GPa and a linear expansivity at constant tension af = 15 x 10 -6 K-1. a) 129.6675 J b) -129.6675 J c) -6.75 J d) 6.75 J

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.48P

See similar textbooks

Similar questions

5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
In 2012, a new fiber-optic cable of handling 40,000 telephone calls simultaneously was laid under the Pacific Ocean from California to Japan, a distance of 13,300 km. The cable was unreeled from shipboard at a mean temperature of 22oC and dropped to the Ocean floor having a mean temperature of 5oC. The coefficient of linear expansion of the cable is 75×10-6 /degree celsius. Determine the length of cable that must be carried on the ship to span the 13,300 Km. Also, find the percent change in length
A 10 kg axial load is uniformly carried by an aluminum alloy pipe with an outside diameter of 10 cm and an inside diameter of 9.6 cm. The pipe is 1.2 m long, Young's modulus for the aluminum alloy is 75 GPa. How much is the pipe compressed?
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shaft carries four masses (150 + 01) kg, (200 + 01) kg, (250 + 01) kg and (300 + 01) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A 50-cm-diameter pipeline in the Arctic carries hot oil at 30◦C and is exposed to a surrounding temperature of −20◦C. A special powder insulation 5 cm thick surrounds the pipe and has a thermal conductivity of 7 mW/m · ◦C. The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2 · ◦C. Estimate the energy loss from the pipe per meter of length. (Please give step-by-step solution)
Steel railroad reels 15 m long are laid with a clearance of 5 mm at a temperature Ti = 34 °C. Assume α = 11.7 μm/(m·°C) and E = 200 GPa. At what temperature in °C will the rails just touch?
A shaft having length equal to 10 m and diameter equal to 70mm is simply supported at both ends. The shaft carries four masses 170 kg, 220 kg, 270kg and 320 kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A cantilever beam, made of cold drawn AISI C1025 steel of circular cross section as shown in the figure below, is subjected to a load which varies from –F to 3F. Determine the maximum load that this member can withstand for an indefinite life using factor of safety N=2. A photoelastic model indicates a theoretical stress concentration factor of Kt=1.42 and the notch sensitivity for a 1/8 in. radius for this material is q=0.9. Analyze at the change of cross section only
A pulley is keyed to a shaft midway between two bearings. The shaft is made of cold drawn steel for which the ultimate strength is 500 MPa and the yield strength is 450 MPa. The bending moment at the pulley varies from – 150 N-m to + 400 N-m as the torque on the shaft varies from – 50 N-m to + 150 N-m. Obtain the diameter of the shaft for an indefinite life. The stress concentration factors for the keyway at the pulley in bending and in torsion are 1.6 and 1.3 respectively. Take the following values: Factor of safety = 1.5; Load correction factors = 1.0 in bending and 0.6 in torsion Size effect factor = 0.85; Surface effect factor = 0.88
A thick-walled cylindrical tubing of hard rubber (k=0.151 W/m*K) having an inside radius of 5 mm and an outside radius of 20 mm is being used as a temporary cooling coil in a bath. Ice water is flowing rapidly inside, and the inside wall temperature is 275 K. The outside surface temperature is 300 K. A total of 20 W must be removed from the bath by the cooling coil. How many meter of tubing are needed?
A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The maximum shear strain occurring in this tank when the contents pressure is 1 MPa, is:
A prismatic bar with a length L = 1 m andcross-sectional area A = 1200mm2 is supported atthe ends. The bar is then subjected to a temperatureincrease of ΔT = 25°C. Calculate the complete state ofstress acting on an inclined section rs that is cut throughthe bar at an angle θ = 45°. Use E = 200 GPa and thecoefficient of thermal expansion α = 12 x 10 -6 / °C .