Please write the complete solutions and Legibly. Thumbs up will given! xyAn element in plane stress is subjected to stresses x = 5,780 psi, ay = 1,130 psi, and t = 695 psi (see the figure below).(Consider only the in-plane stresses the stresses in the x-y-plane).=of=0oyТаDetermine the principal stresses (in psi) and angles of the principle planes (in degrees counterclockwise from the +x-axis).(For normal stresses, use the deformation sign convention.)01 =psi02psi8p18 =p2O5xOfShow the stresses on a sketch of a properly oriented element.

Answered: Image /qna-images/answer/d8d1725c-312e-4749-99a4-2112606b19f2.jpg

An element in plane stress is subjected to stresses ox = 5,780 psi, σy = 1,130 psi, and Txy = 695 psi (see the figure below). (Consider only the in-plane stresses the stresses in the x-y-plane). 02 = Determine the principal stresses (in psi) and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention.) %₁ = psi psi = 8p1 8p2 Show the stresses on a sketch of a properly oriented element. = 50x 0 Of 0

An element in plane stress is subjected to stresses ox = 5,780 psi, σy = 1,130 psi, and Txy = 695 psi (see the figure below). (Consider only the in-plane stresses the stresses in the x-y-plane). 02 = Determine the principal stresses (in psi) and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention.) %₁ = psi psi = 8p1 8p2 Show the stresses on a sketch of a properly oriented element. = 50x 0 Of 0

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
An element in plane stress is subjected to stresses sx= -5500 psi, sy= -2000 psi, and Tx. = 1900 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 6.5 MPa in the vertical direct ion. Also, shear stresses of magnitude 12.5 MPa act in the directions shown (see the figure for Problem 7.2-8). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
An element on the gusset plate in Problem 7.2-23 in uniuxial stress is subjected to compressive stresses of magnitude 6750 psi. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a slope of 1 on 2 (see figure). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. s
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
An element in plane stress is subjected to stresses ??x= 5750 psi, sy = 1100 psi, and txy= 750 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Acting on the sides of a stress element cut from a bar in uniaxial stress are tensile stresses of 10,000 psi and 5000 psi, as shown in the figure. (a) Determine the angle 0 and the shear stress T and show all stresses on a sketch of the element. (b) Determine the maximum normal stress amaxand the maximum shear stress Tmax in the material.
Plastic bar of diameter d = 32 mm is compressed in a testing device by a Force P = 190 N that is applied as shown in the figure. (a) Determine the normal and shear stresses acting: on all faces of stress elements oriented at (1 ) an angle 8 = 00, (2) an angle ?? = 22.5s, and (3) an angle ?? = 45°. In each case, show the stresses on a sketch of a properly oriented element. What are smaxtmax (b) Find smax and tmax in the plastic bar if a re-cantering spring of stiffness k is inserted into the testing device, as shown in the figure. The spring stillness is 1/6 of the axial stiffness of the plastic bar.