An ideal transformer with N, = 2400 and N2 = 400 is connected with an impedance Z2 across winding 2, called secondary. The voltage on the secondary side is V2 = 20415° volts and the current on the primary side is I, = 44- 20° amps. Determine Z2, which is the value of Z2 referred to the primary side of the transformer.

An ideal transformer with N, = 2400 and N2 = 400 is connected with an impedance Z2 across winding 2, called secondary. The voltage on the secondary side is V2 = 20415° volts and the current on the primary side is I, = 44- 20° amps. Determine Z2, which is the value of Z2 referred to the primary side of the transformer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.2P: An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If...

See similar textbooks

Similar questions

Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
Under the assumptions that we made for the ideal transformer, we determined that v2 = (N2/N1)v1. Theoretically, if a dc voltage is applied to the primary of an ideal transformer, a dc voltage should appear across the secondary winding. However, real transformers are ineffective for dc. Use the equivalent circuit of Figure 14.28 on page 728 to explain.
A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are shown below: Open-Circuit Test results from the low voltage side: VOC = 115 V, IOC = 0.1 A, POC = 5 W; Short-Circuit Test results from the high voltage side: VSC = 20 V, ISC = 10 A, PSC = 50 W; Find the transformer’s voltage regulation, in percent, at 50% loading conditions and 0.8 PF lagging. Note: (If %1, the you should write as '1', not as '0,01')
The maximum efficiency of a transformer occurs when the constant core loss equal the variable copper loss. A 25kva transformer is designed so that the maximum efficiency which is 98%, occurs at 70% of rated load and p.f (a) determine the constant core loss in watts (b) determine the full-load copper loss in watt (c) determine the percent efficiency at full load and 90% pf. (Take note 5 decimal places box the answer) Subject Electrical Apparatus and Divices
For the following ideal transformer circuit, the turns ratio N1:N2 is 6:1, Rsupply = 30 kΩ, and Rload = 2.5 kΩ.Find the ac referred primary resistance r1, the primary current i1, the primary voltage v1, the secondary load voltage vload, and the secondary load current iload.
In a 100-kVA, 6,000/400-V, Y-Y, 3-ph, 50-Hz transformer, the copper loss is measured at 5000 W during half-load. Apparently, the maximum efficiency also occurs at ¾ full-load, find the efficiencies of the transformer at full-load and at half-load both at 0.8 pf
A 1000-VA 380 / 110 V conventional transformer is to be used to supply power from a 490-V source to a110-V load. Consider the transformer to be ideal, and assume that all insulation can handle 490 V. (a) Sketch the transformer connection that will do the required job (b) Find the kVA rating of the transformer in the configuration. (c) Find the maximum primary and secondary currents under these conditions