An industrial plant is powered with a delta delta system, along with a transformer bank made up of single-phase transformers of 20KVA, 2300/230 V each. The bank supplies a 40 KVA load with a power factor of 0.7 (-). If a damaged transformer is removed for repair, calculate: a) The load in KVA that each transformer has. b) The nominal load of the transformer bank W.

An industrial plant is powered with a delta delta system, along with a transformer bank made up of single-phase transformers of 20KVA, 2300/230 V each. The bank supplies a 40 KVA load with a power factor of 0.7 (-). If a damaged transformer is removed for repair, calculate: a) The load in KVA that each transformer has. b) The nominal load of the transformer bank W.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.17P: The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of...

See similar textbooks

Similar questions

A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8 kVA, 0.85 lagging power factor load. The input to the transformer is 2400 V, 60 Hz. Neglect the small losses and leakage effects. What will be the apparent power(in kVA) conducted and transformed respectively?
A network is composed of the utility having Ssc=250MVA, and an 2000KVA transformer, rated at 20KV/400V (no load), whose voltage impedance is 7%, and whose load losses are 15750watts. the short circuit at the secondary of the transformer using the impedance method is: a)27.01KA b)None of these c)25.8KA d)30KA
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
a plant is feeding a load 1.2k feet away. the load demands 100 amps at 500V. an ac system with transformer rated 500/5000V near the generating station and 5000/500V near the load. if the line has resistance of 0.2 ohms and receiving voltage of 500V, find the sending end voltage and powerflows and transmission losses.
A 120:480-V, 10-kVA step-up two-winding transformer is to be used as an autotransformer to supply a 120-V circuit from a 600-V source (a step-down autotransformer). When it is tested as a two-winding transformer at rated load, unity power factor, its efficiency is 97.9 %. 1.Show the connection diagram of the transformer converted as an autotransformer and identify which is the series winding Nse and the common winding Nc.
A two-winding transformer rated at 100 kVA, is connected as an autotransformer to provide 10kV from a 15kV supply. Calculate the new rated kVA output. consider the power transformer mode and calculate the related currents Where, Vp = 10000VIp = S/(√3Vp) Is = S/(√3Vs) When find the new currents and voltages proceed to find the primary and secondary powers of the autotransformer. And conclude the rating of the autotransformer.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
A 10MVA 138kV/13.8kV Y-Δ transformer supplies 9.1 MW of resistive load (Δ connected) at the LV side from a 138 kV power grid (infinite bus) at the HV side. Using an ideal transformer model, the line current drawn from the grid in Amperes is?
Using the parameters from the Typical Transformer Values Sheet for a 12.4kV/600V, 100 kVA transformer operating at its rated voltage on the secondary side with its rated load with a PF of 0.8 lagging. Determine for each of the transformer models – deluxe, medium, and economy: Draw the circuit diagram. Find: The magnitude of voltage at the input to the primary side, The power factor on the primary side, The reactive power absorbed by the transformer, The efficiency of the transformer, The voltage regulation of the transformer.
A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following:(a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.