An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18kN/m3, c’ = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if: (i) water table exists far from the slip line

An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18kN/m3, c’ = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if: (i) water table exists far from the slip line

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
The soil of a infinitely long slope has cohesion of value 20 kPa and dry unit weight of 16 kN/m3. If the slope angle is 40° and has a critical height of 5 m, determine the angle of internal friction of the soil.
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface. Also Determine the thrust on the wall if the water table rises to a level 2 m below the surface of the sand. The saturated unit weight of the sand is 20 kN/m3 .
Refer to Figure 15.50. Given that β = 55°, γ = 19 kN/m3, ϕ′ = 17°, c′ = 57.4 kN/m2, and H = 13.7 m, determine the factor of safety with respect to sliding. Assume that the critical sliding surface is a plane.
A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?