An infinitely long conductor is bent into an L shape as shown in Figure. If a direct current of 4 A flows in the conductor, the magnetic field intensity (H) at (2, 2, 0): -0.6792az -0.54336az -0.4075az -0.27168az the magnetic field intensity (H) at (0, - 2, 0) for Q35 0.159az 0.1989 az 0.11934az 0.07956az OO O O

An infinitely long conductor is bent into an L shape as shown in Figure. If a direct current of 4 A flows in the conductor, the magnetic field intensity (H) at (2, 2, 0): -0.6792az -0.54336az -0.4075az -0.27168az the magnetic field intensity (H) at (0, - 2, 0) for Q35 0.159az 0.1989 az 0.11934az 0.07956az OO O O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.12MCQ

See similar textbooks

Similar questions

One thousand circular mils or 1 kcmil is sometimes designated by the abbreviation MCM75C. Data for commercial bare-aluminum electrical conductors lists a 60 Hz resistance of 0.0080 ohm per kilometer at for a 793-MCM AAC conductor. Determine the cross-sectional conducting area of this conductor in square meters. Find the 60 Hz resistance of this conductor in ohms per kilometer at 50C.
With respect to the diagram shown below develop an equation for magnetic field intensity of a currect carrying straight conductor extending from point A to point B, consider dl=dzaz in this case
As seen in Figure-2, the potential on an infinitely wide conductor plane measured. A point load of -3C was placed at (-5.6) and a point load of 4C was placed at (6.8) point. (-2,2) Calculate the potential value and the electric field created at the point. The energy stored in the system calculate. suvject is elctromagnetic field theory.
A cylindrical conductor of radius 1 cm has an internal magnetic field ? = ?0 (?2−?20.03) ?Φ ?/?Find the total current carried by the cylindrical conductor.
The magnetic field intensities inside and outside of a long and smooth conductor with a cross section radius are as follows. Accordingly, find the current densities J inside and outside the conductor. (Hint: Use cylindrical coordinates)
A long straight wire placed along az -axis carries a current of I = 6 A in the +az direction. The magnetic flux density at a distance r = 5cm from the wire will be
The magnetic flux density of sheet steel is smaller than the cast iron for the same value of field intensity True False
A conductor 0.5 m long is moved at right angle to a uniform field strength of 0.12 Wb/m^2 at a speed of 0.2 meter per second. Find the value of emf induced.
Besides the number of turns and the legth of active conductor, whit of the following is?are a factor which affects the amount of emf(voltage) induced in a coil? A) how fast the conductor is moving through the field(rate of incidence), B) the strength of the magtnetic field(flux density), C) the angle at which the conductor is cutting the magnetic field( angle of incidence), D) all of the above What is mean by genarator regulation? A) it is the percentage rise in terminal voltage from no-load to full-load, B) it is the percentage rise in terminal voltage full-load to no-load, C) it is the amount of control one has over the terminal voltage by way of the field excitation, D) none How are transformer components indetified? The algebraic symboly for the number of kilovolt-amperes on the load side of the transformer is_____. A) KVAh, B) KVAx, C) KVA-primary, D) KVA-secondary
Given a magnetic flux density of 0.128 T that is uniform in the positive z direction. What is the magnetic flux: a. across the surface abcd? b. across the surface befc? c. across the surface aefd?
Find the capacitance in picofarad between inner and outer curved conductor surfaces shown in the figure containing two dielectrics, εr1 = 4.9 and εr2 = 3.5. Here r1 = 39.4 mm, r2 = 64.4 mm, α1 = 19.7 degrees, α2 = 41.2 degrees and L = 158.6 mm.
A long, solid, cylindrical wire of radius A has a current density given by j = j0r/A. Determine the magnetic field, within the wire, in terms of the total current "I" flowing through the wire.