An object rotates about a fixed axis, and the angular position of a reference line on the object is given by 0=let, where 0 is in radians and t is in seconds. Consider a point on the object that is 1.46 m from the axis of rotation. At t=1.7s, find the magnitude of the point's radial component of acceleration? Round your answer to zero decimal places.

An object rotates about a fixed axis, and the angular position of a reference line on the object is given by 0=let, where 0 is in radians and t is in seconds. Consider a point on the object that is 1.46 m from the axis of rotation. At t=1.7s, find the magnitude of the point's radial component of acceleration? Round your answer to zero decimal places.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.19P: Plot the earths gravitational acceleration g(m/s2) against the height h (km) above the surface of...

See similar textbooks

Similar questions

The 100 meter diameter wheel needs to be designed so that it rotates at a constant rate and every complete revolution takes 15 minutes. The wheel has been installed in a vertical plane and the lowest seat is 2m above the ground surface. Each ride consists of only one full rotation. Find a further general expression for the horizontal displacement of the rider from its initial position with respect to both time and angle of rotation and hence determine the speed of the rider when t= 180 sec. Using calculus, determine what the maximum horizontal and vertical speeds of the rider would be and at which points during the ride they occur. State expressions for the acceleration of the rider in both horizontal and vertical directions and show that the resultant acceleration experienced by the rider is independent of where on the ride he/she might be. In designing a new wheel with the same diameter and same ride duration as before it is proposed that the wheel’s angular speed should not…
A 124-mm-diameter pipe enlarges to a 139-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 221.912 kilograms per meter cube, and the velocity is 23 meter per second; at section 2 of the larget pipe, the velocity is 15 meter per second. Find the density (in kilograms per meter cube) of the gas at section 2. Round off to three decimal places.
The propeller on Don Karnage's airplane can be modeled as three identical thin rods of uniform density extending radially from the rotational axis of the propeller. To take off, the propeller must accelerate from rest to 633 rpm in 4 s. If the length and mass of each rod are 0.872 m and 3.11 kg, what must be the magnitude of torque in N*m) necessary to accelerate the propeller? Explain how you solved the problem involving something undergoing angular acceleration Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
Show complete solution and 3 decimal places for the final answer. Asap thanks! A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high. The entire mass is 3000kg encountered an unbalanced force of 15kN. Estimate the acceleration in m/s^2.
A circular saw blade 0.6 m in diameter starts from rest and accelerates with constant acceleration to an angular velocity of 100 rad.s-1 in 20 s. Find the angle in degrees through which the blade has turned in the 20-s interval
In the quadratic equation which is homogeneous,a⋅x2+b⋅x+c=0a⋅x2+b⋅x+c=0xx represents a time, cc represents a linear velocity. What are the dimension of aa and bb?
Hi please help me answer this with drawing, thank you. Plot a displacement diagram for a body that is to rise and fall as follows; rise 1 in. in 4 seconds with uniform acceleration, rise 1 in. in 4 sec. with uniform retardation, rest 6 seconds, fall 1 ¼ in. in 6 sec with harmonic motion, rise ½ in. in 3 sec with uniform velocity, fall 1 ¼ in. at once, and rest 4 sec.. Plot displacement as ordinates full size and the time as abscissas to a scale of 1 in. = 4 sec.
A particular bicycle has wheels that are 66 cm in diameter. The radius of the crank armis 18 cm. At its lowest point, the pedal is 16 cm above the ground. A person is pedalingthe bicycle such that the crank arm rotates once every second.Questions:1. Write an equation that models the vertical position of the foot with respect to theground, starting from the lowest point, as the crank arm turns.2. What is the rate of change of the vertical position of the foot when it is at themidline? Explain your answer3. How fast, in kilometres per hour, is the bicycle moving?4. Determine an equation that would model the foot’s position when the cyclist istraveling 5 km/h. Compare this equation to your equation from question 1 andexplain any differences.5. Use calculus to explain why the rotation velocity of a point on the perimeter of awheel is the same as the velocity of the pedal. Use examples to support youranswer.
A shaft 5.0 cm in diameter and rotating at 2,400 rpm, comes to a full stop in 6.0 seconds. It slows down to 1200 rpm during the first 2.0 seconds and comes to a full stop at the end of the sixth second. The acceleration is constant during both segments of the motion. Determine: a.The total number of turns it completes during the 6.0 seconds it is slowing down, b.the distance traveled by a point on the rim of the shaft during this time, and c.the average acceleration during the first 2.0 seconds in rad/s2.
Given: lambda = 10 m, mass of the vehicle, m= 1000kg, k=9000 N/m, speed 60/2pi m/s. Interpret this graph for me. What happens if we go to the right? What happens if we go to the left? If we want to have a great magnitude of vibrations according to the graph should we increase or decrease our speed? explain. What if b is decreasing but we maintain our speed would b decrease or increase the magnitude? Why? If we are driving at the speed that always maximizes the magnitude of the shaking will decreasing b increase or decrease magnitude?
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
A fluid flows through a pipe and exits into a container that sits on some scales. At the beginning of the pipe the velocity is 6m/s After 156s, the scale shows 7733N. The pipe outlet diameter is 0.1m, and is four times greater than the inlet. Determine the density of a fluid