An open rectangular tank 2 meters high, 2 meters wide and 4 meters long is mounted on a truck and fully filled with water. Calculate the volume of water that will be spilled out if the truck from rest accelerated at 2.5 m/sec?.

An open rectangular tank 2 meters high, 2 meters wide and 4 meters long is mounted on a truck and fully filled with water. Calculate the volume of water that will be spilled out if the truck from rest accelerated at 2.5 m/sec?.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Related questions

Q: Q3: A: A half circle of area made from wood, while the other half made from metal. Can you consider ...

Q: A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter ...

A: Given data as per question Length of the bar =10 m Tensile force = 260 kN we know thatNormal stress ...

Q: What are centrifugal pumps' standard pump input power (kW) and water power (kW)?

A: The theoretical minimum power needed to be supplied to the water to increase the pressure of water i...

Q: : Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m 50...

A: It is required to determine the moment of forces about point A

Q: Two cables are tied together at Cand loaded as shown. Knowing that P = 360 N. determine the tension ...

Q: Problem 2 Hinge A stop-block on the edge of the gate at B will break whenever the force reaches 40KN...

Q: Question 1 A light propagates inside a single step index fiber with a speed of 2.0013 × 108?/? and h...

A: Given Datav=2.0013×108m/sα=5.4370°λ=1.48μm-1.60μm

Q: 5. What is the value in m/s^2 of the acceleration of a free falling body?

A: Given:Free falling acceleration induced in the body when it is falling freely downward withoutany ex...

Q: The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass cor...

Q: 3.) In In an actual Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to ...

Q: Q5: Find the both moments of inertia (Ix, Iy) by integration around the central coordinates as shown...

Q: Figure shows a hydraulic elevator which capable to carry 450 kg of passengers from the ground to the...

A: Since we only answer up to 3 subparts so we will answer the first 3. Please resubmit the question by...

Q: QI: determine the resultant of the force system in next figure. And locate the resultant with respec...

Q: Determine the support reactions at A for the propped cantilever beam? 15kN

Q: Q= 2m3/S A= 3 m² determine Slau welocity

A: Given data : The value of discharge=Q The value of area=A To find : Flow velocity

Q: B: Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m 5...

Q: l07 5.니2+ 2.88x108 107 9.60 x107 5.42 t ニ2-1 -レ h-1 400 200 フ

Q: a) For the fixed steel beam shown in Figure 1, use the double-integration method, i) determine the r...

A: Given: A fixed beam with uniform distributed load w. length of the beam=L area moment of inertia of ...

Q: 85 35 55 115 35 125

Q: A cylindrical log (2m in diameter, 1.2m high, and 1.2 m weighing 10.5 kN) floats in water. Its cente...

A: Given: Diameter of the cylindrical log→D=2 m Height of the cylindrical log→H=1.2 m Because weight of...

Q: Q1: determine the resultant of the force system in next figure. And locate the resultant with respec...

Q: An 12-lb force P is applied to a shift lever. Determine the moment of P about B when a is equal to 2...

A: Given Data P=12 lb

Q: Q3: A: A half circle of area made from wood, while the other half made from metal. Can you consider ...

A: It is required to determine the centroid of this circle

Q: Bronze Steel E = 83 GPa E 200 GPa diameter 100 mm diameter 60 mm %3D %3D 1200 kN 900 kN 2.5 m- 3 m

Q: 2. A steady flow, steady state thermodynamic system receives 45 kg/min of a fluid at 207kPa and disc...

Q: Two smooth billiard balls A and B each have a mass of 200 g. A strikes B with a velocity (va)1 = 1.2...

A: Answer: The magnitude of final velocity of A just after collision is 0.640 m/s.

Q: A combined cycle plant with a capacity of 500 MW, which participates in the Mexican wholesale market...

A: This is the manner by which a joined cycle plant creates power while likewise catching waste hotness...

Q: Air at a pressure of 100 kPa and a temperature of 20 °C enters a compressor. It exits the compressor...

A: (i) Write the given data. P1=100 kPaT1=20+273=293 Kηc=0.75P2=400 kPa

Q: A solid steel shaft is to be used to transmit 5 hp from the motor to which is attached. If the shaft...

Q: Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 ...

Q: For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respecti...

A: As given in the question, Maximum stress in the cycle = σmax = 250 MPa Minimum stress in the cycle =...

Q: Q2 Use the analytical method to find the resultant and its direction of the forces shown in figure 1...

A: To solve this problem, first we resolved given forces in x-direction and y-direction, and then calcu...

Q: Problem 2 If a jet of fluid strikes a single body moving with a velocity v, flows over it without fr...

Q: Question 3 2 lb-mass of a mixture (Cp - 3.85 J/g K) must be heated 30 degrees C in 12 seconds. The h...

A: Given, Mass of the mixture = m = 2 lb = 0.907 kg Specific heat of the mixture = Cp = 3.85 J/g-K = 3....

Q: 0.4m The beam is subjected to a shear of y=30 kN. Determine the maximum shear stress in the beam. 0....

A: GivenV=30kNI section beam

Q: The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension in ca...

A: Tension along the cable AB is given as 250 lb. It is required to determine the tension along the cab...

Q: For the beam shown, the magnitude of the distributed load is wo = 10.4 kN/m and the beam length is L...

A: Givenwo=10.4kN/mL=4.8m

Q: A steady, incompressible, inviscid 2D velocity field is given by V 2x + 3y- 5)i +(x– y - 2)j Determi...

Q: Thermodynamics Answer the following questions with complete solutions. write legibly An engine ope...

Q: 3.) Uniform box A has a weight of 40 Ib, and is leaning against box B as shown. Box B has a weight o...

Q: Befinition of confined space from the law with examples of confined spaces Differences between a "re...

A: Given questions to be answered are: Definition of confined space from the law with examples of confi...

Q: Q4 Find the moment about point O in figure 2. 25 N 45 aS 0.5 2.25 m

A: Given

Q: Q1: Calculate the moment of the 0.4 kN force about point O. A et Ww a ana Va y nor de faliatea hanc ...

A: Given Data P=0.4 kN

Q: Q2 Use the analytical method to find the resultant and its direction of the forces shown in figure 1...

Q: I have 250 PSI in tension when I pull on a rope with 200# of Force; what is the area of the rope?

Q: . Air enters a counter flow HE at 70°C and leaves at 40°C. Water enters at 30°C and leaves at 50°C, ...

A: Log mean temperature difference (LMTD) LMTD = ∆T1 - ∆T2ln(∆T1∆T2)

Q: The steel members are pinned at points A, B, and C and are joined by joint D as shown. If the ultima...

Q: Q2: A: Draw the Free Body Diagram only of next fig.

A: Explanation: To draw the free body diagram, we have to keep following points in our mind: ◆ Remove t...

Q: A balloon is filled with pure oxygen at 10 ℃. The balloon is released from the bottom of a water-fil...

A: To given that The volume of the balloon at surface(Vsur)=3000cm3Temperature=25°C=25+273=298KWe konw ...

Q: What is the speed of sound (in ft/s) if the air temperature is 110 °F?

A: To find Speed of sound

Concept explainers

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.

Question

100%

Badly needed Asap.. .I will rate helpful.

An open rectangular tank 2 meters high, 2 meters wide and 4 meters long is mounted on a truck and fully
filled with water. Calculate the volume of water that will be spilled out if the truck from rest accelerated at
2.5 m/sec.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open horizontal tank 3 m high, 3.5 m wide and 6 m long is initially filled at 2 m of water. a. Determine the required acceleration in m/s2 so that no water will be spilled? b. Determine the required acceleration m/s2 so that 1/3 of the initial volume of water will be spilled. c. Determine the remaining volume in cu.m. if it accelerated at 7 m/s^2. d. Determine the minimum hydrostatic force in kN at the side of the tank if 2/3 of the initial volume will be spilled. e. Determine the maximum hydrostatic force in kN at the side of the tank if it accelerates at 3 m/s^2
A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the tank is 10 m long and the depth of the water is 3 m when at rest, Calculate; a) The angle of water surface to the horizontal. b) The maximum pressure intensity on the bottom
In the hydraulic jack shown, a force of 100 N is exerted on the small piston. Determine the upward force on the large piston. The area of the small piston is 65 cm2, and the area of the large piston is 950 cm2. If the small piston moves 12 cm, how far will the large move? Assume the oil to be incompressible.
A 15-ft-long, 6-ft-high rectangular tank open to the atmosphere is towed by a truck on a level road. The tank is filled with water to a depth of 5 ft. Determine the maximum acceleration or deceleration allowed if no water is to spill during towing.
If a pump is capable of lifting 5000kg of water through a vertical height of 60m in 15 min, the power of the pump is
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be
If the pressure 3 m below the free surface of a liquid is 140 kpa, calculate its specific weight and specific gravity.
A car ferry is essentially rectangular with dimensions 25 ft wide and 300 ft long. If 60 cars, withan average weight per car of 3000 lb, are loaded on the ferry, how much farther will it sink intothe water?
Find the density of a metallic body which flows at the interface mercury of specific gravity 13.6 and water such that 40% of its volume us submerged in Mercury and 60% in water.
The friction force between a 6 × 6-ft square sluice gate AB and its guides is equal to 10 percent of the resultant of the pressure forces exerted by the water on the face of the gate. Determine the initial force needed to lift the gate if it weighs 1000 lb.
A water tank in the shape of an inverted right circular cone has an altitude of 15 feet and a base radius of 10 feet. If the tank is full of water, find the work done in pumping all the water over the top of the tank.
For the tank of water shown below, the radius of the circular surface is R=1.0 m, h=1.0m, and the length of the tank is w=2.0 m. Determine (1) the correct expression of the area magnitude whose volume weight is equivalent to the vertical force exerted on the whole curved surfaces_________