An open-topped cylindrical tank contains water that is 80% of its overall height of 1.2 m. The diameter of the tank is 70% of the height. The tank is rotated about its vertical axis. Determine the angular speed in rpm for the following conditions: (7a) maximum value without spilling any water. (7b) value if 25% of its original contents will be spilled. (7c) value if 60% of its original contents will be spilled. (7d) value when the tank is

An open-topped cylindrical tank contains water that is 80% of its overall height of 1.2 m. The diameter of the tank is 70% of the height. The tank is rotated about its vertical axis. Determine the angular speed in rpm for the following conditions: (7a) maximum value without spilling any water. (7b) value if 25% of its original contents will be spilled. (7c) value if 60% of its original contents will be spilled. (7d) value when the tank is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tank has one of its side inclined inward at an angle of 30 degrees with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having its vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev. 14.00m, find the actual velocity of the jet. Neglect air friction. a. 11.3 m/s b. 9.3 m/s c. 8.3 m/s d. 10.3 m/s
A 1.5 m diameter open vessel, 2m high is filled with oil s.g= 0.85 at a depth of 1.6m and rotated at 47 rpm. a. what is the resulting depth of liquid at the center of the vessel? b. what angular speed should be imposed on the vessel such that the liquid touches the bottom surface of the vessel at the center? c. What angular speed should be imposed on the vessel such that there is no liquid 0.47m from the v ertical axis of the vessel?
A cylindrical buoy 100mm in diameter and120mm high is placed vertically inside thetank. The tank is 150mm in diameter andcontains water 200mm deep and oil 30mmdeep. If the buoy weighs 5N, determine thedepth of the buoy submerged.
Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations. Q=10.75m3/s, P=204kw/273hp
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. a. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled. b. Determine the largest pressure developed in the tank.
An open cylindrical tank is two-thirds filled with water. If the tank is 60 cm in diameter and 90 cm high, determine: (Hint: 1 rpm = π/30 rad/s). a.) The maximum rpm required so that no water will be spilled b.) The rpm so that the depth of water at the center of the tank is zero.
A D0 = 12-m-diameter tank is initially filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 95-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V =√ 2gz/(1.5 + fL/D) where z is the water height above the center of the valve. Determine (a) the initial discharge velocity from the tank and (b) the time required to empty the tank. The tank can be considered to be empty when the water level drops to the center of the valve.
A tank has one of its side inclined inward at an angle of 30° with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having it's vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev 14.00 m, find the actual velocity of the jet air friction. Neglect air friction. Include fbd.
An impulse turbine with pitch diameter of 4ft and bucket angle of 160 degree is rotating at 515rpm. The nozzle produces a jet with velocity of 250ft/sec and diameter of 4 inches. Find (a)the force of buckets (b) the torque on runner, (c) the horsepower transferred to the runner, and (d) the efficiency of the turbine. Assume head loss can be expressed as 0.005Vj/2g and assume (v2=v1)
a cylindrical tank is span at 300 rpm its axis vertical. the tank is 0.6 m high and 45cm diameter and is completely filled with water before spinning. calculate the level to which the water will return when the tank stops spinning
A pump draws water from a 20 cm diam suction pipe and discharges through a15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPaat A in the suction pipe. The 15 cm diam pipe discharges horizontally into air atC. To what height h above B can the water be raised if B is 1.8 m. above A and20 hp is delivered to the pump? Assume that the pump operates at 80 %efficiency and that the frictional loss in the pipe between A and C is 3 m. Determine the inclination angle at point C for the water stream to reach a range of 50 m. Also, calculate the maximum height that the water can go from the selected datum plane.
(Q6) Assuming ideal flow in a horizontal plane, calculate the magnitude and direction of the resultant force on the blade. Note that the jet (UC = 15m/s, de= 150mm and UCB=3m/s which moves the blade away from the jet ).The jet UC is divided by the splitter so that one third of the water is discharged from A. ucC 15m/s