ANALYSIS OF STATICALLY DETERMINATE STRUCTURES INFLUENCE LINES Draw the influence line for the force in member CH, and then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 800 Ib/ft which acts along the bottom cord of the truss. 10 ft B |C D 10 ft 10 ft 10 ft 10 ft

ANALYSIS OF STATICALLY DETERMINATE STRUCTURES INFLUENCE LINES Draw the influence line for the force in member CH, and then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 800 Ib/ft which acts along the bottom cord of the truss. 10 ft B |C D 10 ft 10 ft 10 ft 10 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

1. What is the maximum ordinate of the influence line for reaction at E?2. What is the maximum negative moment at B due to moving load of 10 lb/ft?
~#Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming that the loads are being transmitted to the bottom chord. Determine the following member forces while also taking into account the 3-point moving load as illustrated. Assume that the loads only move in the right direction.#~ a. Maximum tension on member DK in kN. b. Maximum compression on member DK in kN. c. Maximum tension on member CI in kN. d. Maximum compression on member CI in kN.
1) A statically determinate beam girder ABCD is overhanging at end is supported by pinned joined at A and roller at C respectively as shown in Figure 2. The beam girder is subjected to a series of concentrated moving loads across the whole beam girder of 7 m span. a. Using static equilibrium equation, draw the influence lines for the reactions at A and C as well as shear force and bending moment at B. Indicate all important values. b. Determine the maximum shear and moment at point B due to a series of concentrated moving loads.
Assume that the loads are being transmitted to the bottom chord in the truss depicted, and draw the influence lines for members DK and CI. Determine the following member forces using the 3 point moving load indicated. Assume the loads only move to the right. Questions a. Maximum tension on member DK in kN. b. Maximum compression on member DK in kN. c. Maximum tension on member CI in kN. d. Maximum compression on member CI in kN.
Use the Müller–Breslau principle to draw the influence lines for the reactions and internal forces for the structure illustrated in Figure 3.6. These reactions and internal forces are: a. Reaction at A, B and C, b. Moment at F c. Shear to the left of support B, and d. Shear to the right of support B.
If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of 114 kN as indicatedin the figure. Using the influence line diagram, (a) determine the max. moment due to loads at C (b) determine max positive V at C
The horizontal load P can act at any location along the length of member AC shown in Figure P12.26. Draw the influence lines for the moment and shear at section 1, and the moment at section 2.
A simply supported beam has a span of 10m. A 7m long udl of 10 kN/m intensity crosses the beam from left to right . When the head of the load is 1m from the right support , find the support reactions , BM and SF at the mid - span using the influence line diagram.
Draw the influence lines for the members JC, EH and HF of the truss shown in Fig. (2), and then determine the maximum tensile force that can be developed in member HF due to moving load of 3kN/m.
1. Draw the influence line for the vertical reaction at internal hinge C. 2. Determine the length and position of a 10kN/m uniformly distributed load that will give a maximum positive shear at C. 3. What is the moment at point D when the previous scenario happens? 4. Determine the maximum moment at D and its location when a 12kN load travels across the beam.
a. Draw the Influence Lines for all support reactions, shear and moment at Bb. Determine the maximum positive shear and bending moment at point B dueto the series of three moving concentrated loads shown in the figure below
Draw the influence lines for members DK and CI assuming that the loads in the illustrated truss are being transmitted to the bottom chord. Considering the provided 3 - point moving load, calculate the following member forces. Assume that the loads only move to the right. Questions a. Maximum tension on member DK in kN. b. Maximum compression on member DK in kN. c. Maximum tension on member CI in kN. d. Maximum compression on member CI in kN.