Another way to prevent a frame from skewing is to triangulate it twice, to make a cross. One brace goes from the top left to the bottom right of the rectangle. The other brace goes from the top right to the bottom left of the rectangle. case A case B Figure 32: Cross-bracing a frame This is called cross-bracing. It is a special kind of triangulation. With cross-bracing the frame does not skew when forces are applied as in case A or case B. 3. Compare the frame design in Figure 31 with the one in Figure 32. (a) Can you use steel cables instead of beams for the braces in both of these frame designs? Explain your answer.

Another way to prevent a frame from skewing is to triangulate it twice, to make a cross. One brace goes from the top left to the bottom right of the rectangle. The other brace goes from the top right to the bottom left of the rectangle. case A case B Figure 32: Cross-bracing a frame This is called cross-bracing. It is a special kind of triangulation. With cross-bracing the frame does not skew when forces are applied as in case A or case B. 3. Compare the frame design in Figure 31 with the one in Figure 32. (a) Can you use steel cables instead of beams for the braces in both of these frame designs? Explain your answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Small screws are used to fasten a piece of hardwood to the bracket that is formed from 1/20-in.-thick steel sheet metal. For steel, γ = 0.283 lb/in.3, and for hardwood, γ = 0.029 lb/in.3 Locate the center of gravity of the assembly. Answer: x¯ = 2.5 in., y¯ = 4.14 in., z¯ = 0.858 in.
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
A square, tied column 410 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 23 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only. ANSWER : 1392.69KN
Replace the loading acting on the beam by a single resultant force. Specify where the force acts, measured from end B.
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m
Compute the internal force of member CD & EF
Problem 11.075 - Determine the vertical deflection of point C caused by the load P Each member of the truss shown is made of steel and has a cross-sectional area of 5 in2. Using E = 29 × 106 psi, determine the vertical deflection of point C caused by the 10-kip load P. (Round the final answer to three decimal places.) The vertical deflection of point C is in. ↓.
Engineering MechanicsDETERMINE FORCE (N) OF MEMBER EG in the truss shown.F1 = 222 NF2 = 513 NF3 = 456 Nα = 43 degreex = 13 m. Note: for compression, include a negative sign ( - ) and for tension, type your answer as is. Input answer in two (2) decimal places.
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
The crowbar is subjected to a vertical force of P = 25 lbat the grip, whereas it takes a force of F = 155 lb at the claw topull the nail out. Find the moment of each force about point Aand determine if P is sufficient to pull out the nail. The crowbarcontacts the board at point A.
The floor system used in a school classroom consist of 4-in. reinforced stone concrete slab. Sketch the loading that acts along the joints BF and side girder ABCDE. Set a= 10 ft. b = 30 ft. Draw FBD and use metric units.
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. w = 4.6 kN/m i need an answer right away. thank you