An radial express feeder used on rural distribution and is connected to a lumped-sum (or concentrated) load at the receiving end. Assume that the feeder impedance is 0.12 + j0.12 p.u. The sending end voltage is 1.05 p.u. and Pr is 1.05 p.u. constant power load, and the power factor at the receiving end is 0.9 lagging. Determine the following K (b) Vr (c) δ (d) Ir

An radial express feeder used on rural distribution and is connected to a lumped-sum (or concentrated) load at the receiving end. Assume that the feeder impedance is 0.12 + j0.12 p.u. The sending end voltage is 1.05 p.u. and Pr is 1.05 p.u. constant power load, and the power factor at the receiving end is 0.9 lagging. Determine the following K (b) Vr (c) δ (d) Ir

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. a) Draw the single-phase wye equivalent circuit and label all known parameters numericallyincluding load voltage. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
A 60 Hz, three-phase transmission line is 100 miles long. It has a total seriesimpedance of {35 + j120) n and a shunt admittance of j930 μsiemen. It delivers40 MW at 220 kV with 90% lagging power factor. Find the voltage at the sendingend by:(a) short line approximation(b) the nominal rr approximation(c) the nominal T approximationAlso determine the voltage regulation for the given line and the power loss.Assume the sending end voltage remains constant. Expected Answer: (a) 237.67 kV, 1.4284 MW, 8.03%; (b) 225.8 kV, 1.1642 MW, 8.67% (c) 225.10 kV, 1.5095 MW, 8.35% Pls. Provide Full Solution for thumbs up
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…