Answer only that first question thanks. A rectangular canal 3.2 m wide and 1.2 m deep has a full capacity of 8.5 m3/s. Assuming n = 0.015 what is the slop of thechannel bed? Water is issued vertically at the rate of 35 L/s through a 60 mm diameter nozzle. What is the the maximum height of water can reach.

Answer only that first question thanks. A rectangular canal 3.2 m wide and 1.2 m deep has a full capacity of 8.5 m3/s. Assuming n = 0.015 what is the slop of thechannel bed? Water is issued vertically at the rate of 35 L/s through a 60 mm diameter nozzle. What is the the maximum height of water can reach.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a rectangular canal with energy height E= 3,5 m, the floor width is given as B= 5,6 m. Neglecting the effects of friction; a) Find the critical depth. b) Calculate the maximum flow that can pass at the given energy level. c) calculate the flow that can pass at a depth of h=2,3 m d) Determine at what depths and regimes the flow of Q= 27 m^3/sec flows. e) Draw the Koch parabola using the data you have obtained.
A pipe of length L = 500 m, diameter D = 300 mm and absolute roughness k = 0.02 mm transports a flow Q = 456 m3/h. Using the Darcy-Weisbach formula determine the hydraulic gradient and headloss through the pipe. The water temperature may be assumed to be 20° C.
A rectangular canal is 2.5 meters wide. The flow rate via the canal is 378 m/s, with a 3.3 cubic m/s flow rate. How deep is the water after the jump?
A 170-m long pipeline, composed of two pipes connected in series, discharges freely at a point 40 m below the water level at intake. The pipe projects into the reservoir. The first 100 m is 25 cm in diameter, and the remaining 70 m is 15 cm in diameter. Assuming that f=0.05 for both pipes, (a) find the rate of flow. If the junction of the two sizes of pipe is 25 m below the intake water-surface level, find the pressure head just above C and just below C, where C denotes the point of junction. Assume a sudden contraction at C. Use k=0.8 for entrance, 0.24 for sudden contraction and 1.0 for exit. I will downvote the incorrect solution
Determine the velocity of flow after hydraulic jump through a 1 m wide channel if the velocity of flow before jump was 2 m/s and the depth was 0.2 m.
A new 45 cm cast-iron pipe 600 m long carries 260 litres/s from reservoir A, discharging into two new cast-iron pipes each 500 m long. One pipe is 30 cm in diameter and leads to reservoir B, in which the water surface is 5 m lower than in A. If the water surface in C is 7 m lower than that at A, determine the diameter of the pipe leading to C. Use n 0.011.
A 40 cm diameter pipe 600 m long carries 260 liters per second of water from reservoir A, discharging into two pipes each 500 m long. One pipe is 30 cm in diameter and leads to reservoir B, in which the water surface is 5 m lower than in A. If the water surface in reservoir C is 7 m lower than that at reservoir A, determine the diameter of the pipe leading to reservoir C. Use Darcy-Weisbach formula with f = 0.022.
The depth of flow of water at a certain section of a rectangular channel 2 m wide is 0.3 m and the flow rate is 1.5 m3/sec. Determine whether a hydraulic jump will occur and if so, calculate its height and loss of energy per kg of water.
A rectangular trough is 10ft long and 3 ft wide. Find how fast the surface rises, if the water flows in at rate of 12 ft³/min.
A channel having a cross-section shown below has a flow rate of 0.023 m^3/s. Compute the hydraulic radius if f=0.022
Determine the elevation of the upstream reservoir (A) in Figure P4.1.2 if the downstream reservoir(B) is at 750m, the flow rate ((water at 20 ℃) through the smooth concrete pipeline is ,1.2m^3/secgiven the following: pipes 1 and 2: 100m long (D=0.5m) valves 1–2: fully open globe valve expansion 2–3: D=0.5m to 1.0m pipe 3: 100m long (D=1.0m) pipe 5: 50m long (D=0.5m) pipe 6: 50m long (D=0.5m) confusor 4: loss coefficient of 0.3 bend 5–6: loss coefficient of 0.2
The rectangular channel is 3 m wide and caries a flow of 10 m3/s. At the 3.5 m drop, water is at the critical depth. Downstream of the drop, the depth = 2 m after the hydraulic jump. The head loss due to the jump = 2 m. (a) What is the depth of water before the jump? Note that the depth you calculate must be in the supercritical range. (b) What is the head loss due to the 2.5 m drop?