Answer two questions, provided that the second is among them Q/ For the post loaded as shown, determine (a) the required tension in rope AC if the resultant of the three forces exerted at point C is to be horizontal, (b) the corresponding magnitude of the resultant. 500 N 25 24 3 L= 1460 mm 200 N 1100 mm B -960 mm-

Answer two questions, provided that the second is among them Q/ For the post loaded as shown, determine (a) the required tension in rope AC if the resultant of the three forces exerted at point C is to be horizontal, (b) the corresponding magnitude of the resultant. 500 N 25 24 3 L= 1460 mm 200 N 1100 mm B -960 mm-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.
The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
The rigid bar AD is supported by two steel wires of 116-in. diameter (E529 3 106 psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D, (b) the corresponding deflection of point D
A T-shaped bracket supports a 288-N load as shown. Determine the magnitude(N) of the vertical reaction at C when α = 25°, x = 137.74 mm, y = 213.66 mm, and z = 300 mm. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the vertical reaction at C using either U if upward or D if downward.
If the magnitude of the resultant force acting onthe bracket is to be 450 N directed along the positive u axis,determine the magnitude of F1 and its direction Φ.
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
9 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 14B) 2C) 6D) 0E) 4
If the bucket weighs 50 lbs, determine the tensions developed in each of the wires. The angle for wire BC and DE is 30deg and a slope of 4 vertical, 3 horizontal for wire BE. Find the tension at wire Fb, tension at wire Fd, tension at wire Fc and tension at wire Fa.
The hot air balloon exerts a 1000 N force along the y-axis. If the allowable tensile stress on the cables attached at points B, C and D is 10 MPa, Determine the safe diameter in mm of the cables. (Note that this problem only have one answer, that is the safe diameter of the cable that is acceptable for all threecables.) Note: Draw the Free Body Diagram, include the proper units and round-off the answers to the nearest whole number.
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14