answer (write the answer only). 1- The open loop voltage gain for ideal op-amp is (zero, unity, infinity, none). 2- In sample and hold circuit the op-amp is used as (comparator, voltage follower, detector, multiplier) 3- Current-shunt negative feed-back stabilizes (voltage gain, current gain, trans-conductance, trans-resistor) 4- To obtain high input resistance and low output resistance, the feedback topology needed is (voltage-shunt, current-series, current-shunt, voltage series). 5- The lowest distortion factor in power amplifier is obtained using class (A, B. AB, C). 6- Open loop mode op-amp can be used in (amplifier, comparator, filter, oscillator). 7- Impedance matching in tuned amplifier is used to improve ( bandwidth, gain, input resistance, output resistance). 8- Output resistance of ideal buffer is (zero, unity, infinity, none). 9- Crystal type oscillators is used to provide (stable output frequency, low power consumption, high gain, high input impedance). 10- For a 4-bit flash type A/D convertor, the number of comparators required is (3, 7, 11,15). Please send the solution quickly

answer (write the answer only). 1- The open loop voltage gain for ideal op-amp is (zero, unity, infinity, none). 2- In sample and hold circuit the op-amp is used as (comparator, voltage follower, detector, multiplier) 3- Current-shunt negative feed-back stabilizes (voltage gain, current gain, trans-conductance, trans-resistor) 4- To obtain high input resistance and low output resistance, the feedback topology needed is (voltage-shunt, current-series, current-shunt, voltage series). 5- The lowest distortion factor in power amplifier is obtained using class (A, B. AB, C). 6- Open loop mode op-amp can be used in (amplifier, comparator, filter, oscillator). 7- Impedance matching in tuned amplifier is used to improve ( bandwidth, gain, input resistance, output resistance). 8- Output resistance of ideal buffer is (zero, unity, infinity, none). 9- Crystal type oscillators is used to provide (stable output frequency, low power consumption, high gain, high input impedance). 10- For a 4-bit flash type A/D convertor, the number of comparators required is (3, 7, 11,15). Please send the solution quickly

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

1. A non-inverting op-amp circuit has the open loop gain of 105 and the resistances R1 = 1k Ω and R2 = 39k Ω . Calculate (a) The actual value of voltage gain, (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
A non-inverting op-amp circuit has the open loop gain of 104 and the resistances R1 = 2k Ω and R2 = 50 k Ω. Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Activity 2:You are asked to examine the performance of three op-amp circuits. 2-A) Categorize the circuits in terms of using a feedback or not, and the specific type of thefeedback connection (positive or negative, shunt or series, voltage or current).2-B) Explain the principle of operation of Circuit A. Explain limitations of this circuit in termsof practical applications. What is the technical name describing this circuit?2-C) Explain the principle of operation of Circuit B. What is the advantage of this circuitcompared to Circuit A? What is the technical name describing this circuit?2-D) Explain the principle of operation of Circuit C. What is the advantage of this circuitcompared to Circuits A and B? What is the technical name describing this circuit?2-E) Draw the block diagram of Circuit C and define the forward path gain A and feedbackpath gain β. Derive the overall circuit gain relating input to output.2-F) Build all circuits in MultisimTM using one ‘uA741CP‘op-amp IC fed by…
An inverting amplifier has closed-loop voltage gain of 100. The op-amp has an open-loop voltage gain of 100000. If a different op-amp with open-loop gain of 200000 is substituted in the configuration, the closed-loop gain increases/decreases and why?
Figure Q2(a) shows an amplifier system with the given input voltagewaveform Vin and the corresponding output voltage waveform Vout. If a practical op-amp is used in the amplifier system in Figure Q2(a),calculate the closed-loop gain, ACL given that the open-loop gain, AOL =3000. You can use the value of resistances found in Q2(a)(i).
In the op amp model above, open-loop gain is 105 and Vcc=12V. Suppose the inverting-input voltage is vn=44μV and the noninverting input voltage vp=284μV. What is the op-amp’s output voltage vo (in volts)?
In the op amp model above, open-loop gain is 106 and Vcc=12V. Suppose the inverting-input voltage is vn=90μV and the output voltage vo=5V. What is the noninverting input voltage vp (in micro-volts)?
A non-inverting op-amp circuit has the open loop gain of 136 and the resistances R1=3500 Ω and R2 = 3.8 kΩ . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain. (a) The actual value of voltage gain Answer for part 1 (b) The ideal value of voltage gain Answer for part 2 (c) Error, when ideal voltage gain is compared with actual voltage gain. Answer for part 3 (d) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Derive the closed loop and open loop gain equations of the inverting amplifier in terms of R1 and R2
Determine the closed-loop voltage gain of the circuit shown in the figure assumingan ideal op amp
Calculate the closed-loop voltage gain, ACL, of an inverting op-amp circuit having an input resistance of 3 kilo-ohms and a feedback resistor of 150 kilo-ohms. choices: a. 150b. 250c. 50d. 125
1. Assuming the op amp to be ideal, derive an expression for the closed-loop gain of the circuit shown in Figure 1.