Ap Q1) Determine the total input resistance of the emitter-follower in Figure 1. Also find the voltage gain, current gain, and power gain in terms of power delivered to the load, RL. Assume ß-175 and that the capacitive reactance's are negligible at the frequency of operation. Vcc -O +10 V the R₁ 18 ΚΩ C₁ V in 3 V rms R₂ 51 ΚΩ F 1 μF ww W +1₁ 2N3904 C₂ 10 μF RE 470 Ω 마 Vo out Www R₁ 470 (2

Ap Q1) Determine the total input resistance of the emitter-follower in Figure 1. Also find the voltage gain, current gain, and power gain in terms of power delivered to the load, RL. Assume ß-175 and that the capacitive reactance's are negligible at the frequency of operation. Vcc -O +10 V the R₁ 18 ΚΩ C₁ V in 3 V rms R₂ 51 ΚΩ F 1 μF ww W +1₁ 2N3904 C₂ 10 μF RE 470 Ω 마 Vo out Www R₁ 470 (2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the Value of output voltage Vo(t), in volts (V), after two seconds given the input signal below and the value of R = 1Kohm, C = 0.1uF and the period (T) of input signal is 1 second.
Electronic Consider the circuit shown in figure, where be=710 mV, B = 100, and VA = ∞. Assume that the emitter current is equal to collector current. Sekildeki devre için BE=710 mV, B = 100 ve VA = ∞ oldugunu dikkate aliniz. Emiter akiminin kollektör akimina esit oldugunu kabul ediniz. Circuit parameters / Devre Parametreleri Rg = 30 kM, Rc = 400 R, RE = 400 R, Vcc = 4 V -> Alttaki devre için Q, transistörunün kollektor akimini Ic belirleyiniz. (Determine the collector current Ic of Q, for the circuit shown below.) (dogru katsayisi: 0.5) -> Alttaki devre için Q, transistörunün kollektör gerilimini Vc belirleyiniz. (Determine the collector voltage Vc of Q, for the circuit shown below.) (dogru katsays:: 0.5)
transistor datasheet. 1. COMPLETE TABLE #1 Table 1 Parameters of BJT transistors Code type Ic [A] VCEO [V] PD[w] ft[MHz] encapsulated 2N2222A 2N3904 2N3906 NPN 0.2A 40V 0.625W 300MHz TO-92 MPS2907A PNP 0.8A 60V 0.4W 200MHz TO-92
Calculate the output impedance for small-signal equivalent circuit. (R1=10 k ohm, r0, =10 k ohm)
The gain of vertical deflection amplifier in CRT is 90. If an input signal of 110mV is applied, it will produce electrical field of 33V/cm and vertical deflection of electrons beam on the center of plates of 4.31x10-3 cm with an angular deflection given by arctan (0.0137). The electrons enter the plates with a velocity of 3.2479x109 cm/sec, and deflection sensitivity of 0.055cm/V. Determine: 1) The dimensions of vertical deflection plates {long, a part (l,d)}. 2) The distance from the end of deflection plates to the screen. { 2.5cm, 0.3cm, 38.49cm}
Derive a mathematical expression to determine the stability factor for Fixed-bias circuit1- S(ICO) 2- S(VBE) 3- S(β)
14 - Which of the following is IC / IB (the ratio of collector current to base current) in a transistor?A) Dielectric coefficientB) Conversion rateC) Beta current gainD) Alpha current gainE) The conductivity coefficient
Class B Amplifier q1)If the input is 7.5Vp-p...DATA COLLECTION: What is the IL(peak)? a)7mA 6)mA 5)mA 4)mA q2) DATA COLLECTION: What is the Idc? a)3.84 b)4.82 c)3.82mA d)1.82mA q3)DATA COLLECTION: What is the input power in DC? Power input = 48.45mW Power input = 45.48mW Power input = 44.58mW Power input = 45.84mW q4) DATA COLLECTION: What is the output power in AC? a)18mW b)81mW c)11.8mW d)18.9mW q5)DATA COLLECTION: What is the power dissapated by each transistor? a)35.1mW b)53.1mW c)15.3mW d)13.5mW q6)DATA COLLECTION: What is the efficiency of class B amplifier? a)45% b)40% c)63% d)33% q7)
Multiple Choice directions: Circle the letter of the answers that best answer the question. 13. When using microwave tubes as amplifiers, what is used as bandpass filters? a. Transistors b. Oscillator c. All of the above d. Power tubes 14. The microstrip lines used to achieve maximum power transfer are intended for a. Signal coupling b. Decoupling to prevent feedback c. Low-noise amplification d. Impedance matching and tuning 15. A diode that when reverse biased will momentarily and will abruptly turn off. a. Varactor diode b. IMPATT c. Step recovery diodes d. PIN diodes 16. A microwave transmission line used to minimize noise and crosstalks. a. Stripline b. Hard line cable c. Waveguide d. Microstrip 17. The major difference between a low frequency transistors and microwave types is/are. a. B & C b. Packaging c. Material d. Internal geometry 18. Which of the following band belongs to the millimeter waves a. C b. Ku c. U d. L 19. Overcrowding in the frequency spectrum is prevalent…
One of the following is not a property of a common-emitter amplifier: Select one: a. high voltage gain b. No phase inversion c. high current gain d. Emitter is at ac ground
Using the circuit shown in figure 1 below, design a Wien-bridge circuit to oscillate at a frequency of 100 kHz.
Determine the required values of R1, R2, Rc, and RE. Also, determine the expected output voltage if the input voltage is equal to 0.001 Vrms. GIVEN: Zi = 1145.66 ohms Zo = 3.3 Kohms Beta = 80 Vcc = 20V R1 + R2 = 43.7 Kohms Av = 167.43 Ai = 58.13