Apparatus: [1] mini mechatronics PLC Trainer [2] SIMATIC S7-300 PLC [3] PC with Step 7 software [4] Connection wires [5] Toggle switch (or selector switch) [6] Pneumatic pump and connection pipes Experimental Procedure: You are requested to use SIMATIC S7-300 PLC to control the following operations on the mini-mechatronics kit. Make all required connections between PLC I/O ports and the mini- mechatronics kit I/O terminal rail. Write a Step 7 program to control the following operations: 1. Place two parts in the feeding magazine (metallic and nonmetallic). 2. Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if Toggle is ON. 3. The ejector plate of the supply unit should push one part onto the conveyor. 4. The conveyor turns on and transfers the part past the sensor unit, where it is checked for type, to the stopper unit. 5. If the part is metallic, the stopper gate will open, allows piece to pass through then will close. The metallic piece will keep moving on the conveyor until it drops into the container at the end of the line, then the conveyor stops. 6. If the part is plastic, when it reaches the stopper, the conveyor stops, the z-axis cylinder goes down, the suction pad picks the part up, and then the z-axis retracts. The x-axis cylinder extends to drop the part onto the workpiece 3-position holding platform, while the cylinder is in the upper position (without lowering the z-axis). The x-axis retracts to initial position. 7. The process repeats. 8. Use the counters to count the different types of workpieces processed through the system.
Apparatus: [1] mini mechatronics PLC Trainer [2] SIMATIC S7-300 PLC [3] PC with Step 7 software [4] Connection wires [5] Toggle switch (or selector switch) [6] Pneumatic pump and connection pipes Experimental Procedure: You are requested to use SIMATIC S7-300 PLC to control the following operations on the mini-mechatronics kit. Make all required connections between PLC I/O ports and the mini- mechatronics kit I/O terminal rail. Write a Step 7 program to control the following operations: 1. Place two parts in the feeding magazine (metallic and nonmetallic). 2. Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if Toggle is ON. 3. The ejector plate of the supply unit should push one part onto the conveyor. 4. The conveyor turns on and transfers the part past the sensor unit, where it is checked for type, to the stopper unit. 5. If the part is metallic, the stopper gate will open, allows piece to pass through then will close. The metallic piece will keep moving on the conveyor until it drops into the container at the end of the line, then the conveyor stops. 6. If the part is plastic, when it reaches the stopper, the conveyor stops, the z-axis cylinder goes down, the suction pad picks the part up, and then the z-axis retracts. The x-axis cylinder extends to drop the part onto the workpiece 3-position holding platform, while the cylinder is in the upper position (without lowering the z-axis). The x-axis retracts to initial position. 7. The process repeats. 8. Use the counters to count the different types of workpieces processed through the system.
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Kreith, Frank; Manglik, Raj M.
Chapter7: Forced Convection Inside Tubes And Ducts
Section: Chapter Questions
Problem 7.2DP
Related questions
Question
Please draw PLC diagram on plc software for this procedure
![Apparatus:
[1] mini mechatronics PLC Trainer
[2] SIMATIC S7-300 PLC
[3] PC with Step 7 software
[4] Connection wires
[5] Toggle switch (or selector switch)
[6] Pneumatic pump and connection pipes
Experimental Procedure:
You are requested to use SIMATIC S7-300 PLC to control the following operations on the
mini-mechatronics kit. Make all required connections between PLC I/O ports and the mini-
mechatronics kit I/O terminal rail.
Write a Step 7 program to control the following operations:
1. Place two parts in the feeding magazine (metallic and nonmetallic).
2. Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if
Toggle is ON.
3. The ejector plate of the supply unit should push one part onto the conveyor.
4. The conveyor turns on and transfers the part past the sensor unit, where it is checked
for type, to the stopper unit.
5. If the part is metallic, the stopper gate will open, allows piece to pass through then will
close. The metallic piece will keep moving on the conveyor until it drops into the
container at the end of the line, then the conveyor stops.
6. If the part is plastic, when it reaches the stopper, the conveyor stops, the z-axis cylinder
goes down, the suction pad picks the part up, and then the z-axis retracts. The x-axis
cylinder extends to drop the part onto the workpiece 3-position holding platform, while
the cylinder is in the upper position (without lowering the z-axis). The x-axis retracts to
initial position.
7. The process repeats.
8. Use the counters to count the different types of workpieces processed through the
system.](/v2/_next/image?url=https%3A%2F%2Fcontent.bartleby.com%2Fqna-images%2Fquestion%2Fa17f9023-1421-4642-8114-70f4142ecf5c%2F69073a91-0762-4e76-b56b-603390550cf6%2F7saeks_processed.jpeg&w=3840&q=75)
Transcribed Image Text:Apparatus:
[1] mini mechatronics PLC Trainer
[2] SIMATIC S7-300 PLC
[3] PC with Step 7 software
[4] Connection wires
[5] Toggle switch (or selector switch)
[6] Pneumatic pump and connection pipes
Experimental Procedure:
You are requested to use SIMATIC S7-300 PLC to control the following operations on the
mini-mechatronics kit. Make all required connections between PLC I/O ports and the mini-
mechatronics kit I/O terminal rail.
Write a Step 7 program to control the following operations:
1. Place two parts in the feeding magazine (metallic and nonmetallic).
2. Press a Toggle start/stop (ON/OFF) switch to initiate the system. System works only if
Toggle is ON.
3. The ejector plate of the supply unit should push one part onto the conveyor.
4. The conveyor turns on and transfers the part past the sensor unit, where it is checked
for type, to the stopper unit.
5. If the part is metallic, the stopper gate will open, allows piece to pass through then will
close. The metallic piece will keep moving on the conveyor until it drops into the
container at the end of the line, then the conveyor stops.
6. If the part is plastic, when it reaches the stopper, the conveyor stops, the z-axis cylinder
goes down, the suction pad picks the part up, and then the z-axis retracts. The x-axis
cylinder extends to drop the part onto the workpiece 3-position holding platform, while
the cylinder is in the upper position (without lowering the z-axis). The x-axis retracts to
initial position.
7. The process repeats.
8. Use the counters to count the different types of workpieces processed through the
system.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 2 steps with 1 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi…
Mechanical Engineering
ISBN:
9781305387102
Author:
Kreith, Frank; Manglik, Raj M.
Publisher:
Cengage Learning
Principles of Heat Transfer (Activate Learning wi…
Mechanical Engineering
ISBN:
9781305387102
Author:
Kreith, Frank; Manglik, Raj M.
Publisher:
Cengage Learning