Q2: From the following excerpt of field notes, plot the cross section on graph paper and superimpose on it a design template for a 40-ft-wide level roadbed with cut slopes of 3:1 and a subgrade elevation of 1239.50 ft. Determine the area by coordinate method. HI = 1254.80 ft 46 + 00 Lt 8.0 7.9 5.5 4.9 6.6 7.5 60 27 10 0. 24 60

Q2: From the following excerpt of field notes, plot the cross section on graph paper and superimpose on it a design template for a 40-ft-wide level roadbed with cut slopes of 3:1 and a subgrade elevation of 1239.50 ft. Determine the area by coordinate method. HI = 1254.80 ft 46 + 00 Lt 8.0 7.9 5.5 4.9 6.6 7.5 60 27 10 0. 24 60

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the sketch ATTACHED, determine the horizontal distance AB and the elevation of Point B Starting Elevation at A is 50.00’ S (slope dist.) = 822.48 feet, Z (zenith angle) = 88º, hi = 5.15’, r = 5.00’
A closed five-sided field traverse has the following interior angles: A = 121°13′00″; B = 136°44′30″; C = 77°05′30″; D = 94°20′30″. Find the angle at E.
1. A traverse line was measured in three sections: 295.85 m at slope 8045’, 149.58 m at slope 4029’ and 373.48 m. at slope 4025’. Determine the horizontal length of the line.
3. Shown in the accompanying sketch are the measured offsets from a traverse line AB to an irregular boundary and the spacing between the offsets. Find the area using: a) Mid Ordinate Rule b) Average-ordinate Rule c) Trapezoidal Rule d) Simpson’s Rule
From the base line AB, the linear measurements (offsets) are taken to setting out a rectangular fence CDEF, find CD”, DE~ knowing that AB~ = 170° 5.
Show illustration/diagram with complete and detailed solution. Compute the area of a cross section: Formation width 18 mDepth of cut at the midpoint of formation 3 mTransverse slope on the right side of midpoint 10 to 1Transverse slope on the left side of midpoint 7 to 1Side slope 2.5 to 1
A pentagonal lot has the following data. SIDE AZIMUTH DISTANCE(M) AB 198° 30' 108.20 BC 288° 98.60 CD 356° 30' 112.40 DE 42° 20' 120.00 EA ? ? Find the following: a) bearing and distance (m) of line EA b) area of the lot ( in m2 ) and (in hectare) c) DMD (Double Meridian Distance) of line BC d) DPD (Doubel Parallel Distance) of line DE Kindly show a full and detailed solution, thank you!
By the trapezoidal rule, find the area between a traverse line and a curved boundary, rectangular offsets being taken at intervals of 5 meters, and the values of the offsets being h1 = 3.2, h2 = 3.4, h3 = 12.8, h4 = 11.2, and h5 = 4.4.
A topographic surveying map using a scale 1cm: 40 m, and with a contour interval of 1.0 m. a The distance scaled on the map between two adjacent contours is 15 mm. Determine the slope of the ground in percent. Options A 1.56% B 1.65% C 1.76% D 1.67%
The following interior angles of a pentagon traverse were measured with same precision. Determine the most probable value of angles A, B, C, D, and E. Show full solutions.
on a map the scaled distance between points a and b is 15.45cm and the given elevationof the two points are 815.26m and 836.45m, respectively. assuming uniformity of slope between two points, calculate the distance from point a and the map where each of the following contour lines will cross the line joining the two points: 820, 825, 830, and 835.
Given a rectangular tract of land 690m by 1220m, the elevation at the center of the tract (E) is 165.0m and the elevation of corners A,B,C and D are 62.5m, 93.3m, 212.8m and 125.3m, respectively. Assuming uniformity of slope between the given corners, and contour interval of 20m, you are required to plot the contour lines. The contour lines with elevations of 100m and 200m to be shown as index contours.