Argon is heated at 340 K with a mass flow of 3 kg/s while passing through a pipe. Given that the heat taken by the argon is 29 kW and the flow is known to be continuous, which of the following is the temperature at the pipe outlet? (Cp = 0.5203 kJ/kgºC) a) 95.7 ºC B) 75.3 ºC NS) 358.6 ºC D) 85.6 ºC TO) 348.3 ºC

Argon is heated at 340 K with a mass flow of 3 kg/s while passing through a pipe. Given that the heat taken by the argon is 29 kW and the flow is known to be continuous, which of the following is the temperature at the pipe outlet? (Cp = 0.5203 kJ/kgºC) a) 95.7 ºC B) 75.3 ºC NS) 358.6 ºC D) 85.6 ºC TO) 348.3 ºC

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 29RQ: If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the...

See similar textbooks

36 -

95.7 ºC

75.3 ºC

NS)

358.6 ºC

85.6 ºC

TO)

348.3 ºC

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Unreasonable Results - A slightly deranged Arctic inventor surrounded by ice thinks it would be much less mechanically complex to cool a car engine by melting ice on it than by having a water-cooled system with a radiator, water pump, antifreeze, and so on. (a) If 80% of the energy in 1.00 gal of gasoline is converted into “waste heat” in a car engine, how many kilograms of 0C ice could it melt? (b) Is this a reasonable amount of ice to carry around to cool the engine for 1.00 gal of gasoline consumption? (c) What premises or assumptions are unreasonable?
3. Steam enter a turbine with an enthalpy of 1292 Btu/lb anf leaves with an enthalpy of 1098 Btu/lb. The transferred heat is 13 BTU/lb. What is the work in BTU/min an in h for a flow of 2 lb/sec? 3 decimal in final answer pls
A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m3. (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind turbine?
Why did you multiply 249.57 gal/s by the density of water, 8.34 lb/gal? 249.57 gal/s is the flow rate of air, NOT water.
If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the volume of air, in ft3, exiting the evaporator coil?
A pump has a flow rate of 0.5 m3/min. The pump head is 12 m. (a) Determine the pump head in m^2/s^2. Answer Check: 118 m^2/s^2 (b) Determine the pressure change across the pump. Answer Check: 118,000 Pa (1Pa = 1kg/m s^2) (c) Determine the work required for a 100% efficient pump. Answer Check: 980 W (d) Determine the work required for a 85% efficient pump. Answer Check: 1.15 kW
SG of Water=1.0 SG of Mercury=13.6 SG of n-Octane=0.65
Engineering economics Investing in Electrical Efficiency Two pumps capable of delivering 100 hp to an agricultural application are being evaluated in a present economy study. The selected pump will only be utilized for one year, and it will have no market value at the end of the year. Pertinent data are summarized as follows: ABC Pump XYZ PumpPurchase price $2,900 $6,200Maintenance cost $170 $510Efficiency 80% 90% If electric power costs $0.10 per kWh and the pump will be operated 4,000 hours per year, which pump should be chosen? Recall that 1 hp = 0.746 kW. Choose XYZ because it provides least cost.
2- Please I want a solution of this question. Many Thanks Determine the average wind velocity required to produce 4 MW of effective power by a wind turbine having the following data: blade length 65 m, hub diameter 6 m, air density 1.12 kg/m3, power coefficient 0.6, gear efficiency 85%, electrical efficiency 90% and generator efficiency 95%.
7 g = 10 m/s^2
solve. heat transfer
An electric boiler generates 100,000 Btus of heat. Roughly, what is the electrical input of the boiler (in other words, the electrical energy to produce the output), in kilo-watts?