As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G = 42 GPa. Compute the maximum shearing stress in each spring using Wahl formula. Steel A800 2m Steel 4m 50 kg Phosphor Bronze

As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G = 42 GPa. Compute the maximum shearing stress in each spring using Wahl formula. Steel A800 2m Steel 4m 50 kg Phosphor Bronze

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.10P: The tensional pendulum shown in the figure consists of a horizontal circular disk of a mass M = 60...

See similar textbooks

Similar questions

The tensional pendulum shown in the figure consists of a horizontal circular disk of a mass M = 60 kg suspended by a vertical steel wire (G = SOGPa) of a length L = 2 m and diameter d = 4 mm. Calculate the maximum permissible angle of rotation <£m:ls of the disk (that is, the maximum amplitude of torsional vibrations) so that the stresses in the wire do not exceed 100 MPa in tension or 50 MPa in shear.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A rigid plate of negligible mass rests on the middle spring which is higher than the two outer springsby 20 mm. The middle spring consists of 24 turns of 25-mm diameter wire on a mean diameter of 150mm. The two outer springs have 16 turns of 12-mm diameter wire on a mean diameter of 100 mm.Determine the shearing stress developed in each spring if P = 5 kN is applied. Use the Approximateformula.
As shown in the figure, a homogeneous 50 kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10 mm diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20 mm diameter wire on a mean diameter of 150 mm and G = 42 GPA. Compute the shearing stress in each spring, use Wahl’s Equation.
When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a torsional resistance TA. Also, soil along the sides of the pipe creates a distributed frictional torque along its length, varying uniformly from zero at the surface B to tA at A. Determine the minimum torque TB that must be supplied by the drive unit to overcome the resisting torques, and calculate the maximum shear stress in the pipe. The pipe has an outer radius ro and an inner radius ri.
A heavy-duty helical spring is to be made by wrapping a steel rod 10.6 mm in radius aroundforming cylinder 141 mm in diameter. If the elongation and shearing stress are limited to 161mm and 141 MPa, respectively. How many turns are required approximately? G = 83 GPa. Useapproximate formula for shear stress
Calculate the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm-diameter wire when the spring is stretched 100 mm. G = 42 GPa
As shown in the figure, a homogeneous 100-kgrigid block is suspended by the three springs whoselower ends were originally at the same level. Eachsteel spring has 24 turns of 10-mm-diameter on amean diameter of 100 mm, and G = 83 GPa. Thebronze spring has 48 turns of 20-mm-diameterwire on a mean diameter of 150 mm, and G = 42GPa. Compute the maximum shearing stress ineach spring using A.M. Wahl formula.
Determine the mazimum shearing stress (using approximate and exact equations) and elongation of a helical spring considering of 22 turns of 15mm diameter wire on a mean coil radius of 100mm when the spring is supporting a load 1.3KN. Use G=83-Gpa
Determine the maximum shearing stress in MPa of a helical spring composed of 20 turns and 19 mm wire diameter on a mean radius of 75 mm when the spring is supporting a load of 1000 N, assume the modulus of rigidity of 83 GPa.