AS SHOWN IN THE FIGÚRE, A RIGID BEAM WITH NEGLIGIBLE MASS IS PINNED AT 'O' AND SUPPORTED BY TWO RODS IDENTICAL EXCEPT FOR LENGTH. A = 100 mm2 & E= 200 GPA. DETERMINE THE LOAD IN EACH ROD IF P = P3. -1m- -L1 D PROB 02 L1 = 5m L2 = 6m L3=7m P1 = 7 KN P2 = 2 KN P3 = 9 KN W1 = 4 KN/m W2 = 3 KN/m B = 350 mm

AS SHOWN IN THE FIGÚRE, A RIGID BEAM WITH NEGLIGIBLE MASS IS PINNED AT 'O' AND SUPPORTED BY TWO RODS IDENTICAL EXCEPT FOR LENGTH. A = 100 mm2 & E= 200 GPA. DETERMINE THE LOAD IN EACH ROD IF P = P3. -1m- -L1 D PROB 02 L1 = 5m L2 = 6m L3=7m P1 = 7 KN P2 = 2 KN P3 = 9 KN W1 = 4 KN/m W2 = 3 KN/m B = 350 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft shown is attached to a rigid supports. For bronze segment AB, the diameter is 75 mm, maximum shearing stress is 60 MPa, and G = 35 GN/m^2. For steel segment BC, the diameter is 50 mm, maximum shearing stress is 80 MPa, and G = 83 GN/m^2.1. Which of the following most nearly gives the ratio torque carried by bronze to torque carried by steel? a. 1.2b. 1.8c. 1.6d. 2.02. Which of the following most nearly gives the torque carried by the bronze in kN.m?a. 4.98b. 9.15c. 6.53d. 3.143. Which of the following most nearly gives the maximum torque T than can be applied in kN.m? a. 6.4b. 5.1c. 4.3d. 7.8
A flat brass bar has length L, constant thicknesst, and a rectangular cross section whose widthvaries linearly between b2 at the fixed support to b1at the free end (see figure). Assume that the taper ofthe bar is small. The bar has modulus of elasticity E.Calculate the displacements δB and δC if P = 200 kN,L = 2 m, t = 20 mm, b1 = 100 mm, b2 =115 mm,and E = 96 GPa.
'The I-beam is loaded as shown in the figure. Determine the required flange width b so that the stress caused by bending does not exceed the allowable stress σmax = 170 MPa. The thickness of the flange is tflange= 12 mm, and the thickness of the web inch tweb= 8 mm, so let's look at just bending. F = 48kN, q = 8kN/m, L = 2.2m, H = 500mm Use units [N, mm]. Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!
AS SHOWN IN THE FIGURE, A RIGID BEAM WITH NEGLIGIBLE MASS ISPINNED AT ‘O’ AND SUPPORTED BY TWO RODS IDENTICAL EXCEPT FORLENGTH. A = 100 mm2 & E = 200 GPa. DETERMINE THE LOAD IN EACHROD IF P = P3
q2: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.705 m, b = 1.821 m, and L= 4 M.For a load of P = 117 kN, determine thedisplacement of joint F. Unit should be in mm
Determine the length of b and d (shown in Figure 2) of a square column of steel withyield strength of 175 MPa and E = 190GPa to carry loads of 1610 kN.
A horizontal beam AB with dimensions of its cross section (b = 19 mm) x (h = 200 mm) is supported by a rake CD and supports a load P = 12 kN at B (see part a of the figure). The strut, consisting of two bars each with a thickness of 5b/8, is connected to the beam by a bolt that passes through the three bars that meet at C (see part b of the figure) (a) If the allowable shear stress in the bolt is 90 MPa, what is the necessary minimum diameter (dmin) of the bolt at C? (b) If the allowable bearing stress in the bolt is 130 MPa, what is the necessary minimum diameter (dmin) of the bolt at C?
A cantilever beam shown in Figure B2 is applied with point load of 10KN and pointmoment of 7KNm. By using Macaulay method:Sebuah rasuk terjulur dikenakan beban tumpu 10KN dan moment lentur 7KNmseperti yang ditunjukkan dalam Rajah B2. Dengan menggunakan kaedah Macaulay:i) Derive the moment equation for the beam Terbitkan persamaan momen bagi rasuk
A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
In the loaded truss shown, AB=BC=CD=DE=3.4 m, BF=CG=GI=DH=HJ=(EK)/2=5.1 m. If the loading P=3.3 kN, calculate the force (in kN with proper sign) in member HK (correct to 1 decimal place). (sign convention: tensile force in a member is taken with positive sign)
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
Find the value q can take so that the BD bar, the cross section of which is shown in the figure, can carry the given load without buckling. factor of safety n = 3 Ri= 7cm , Rd=9cm on BD bar