ASAP NEED IN 1 HOUR I'LL GIVE UPVOTEDesign a 3.66 m simply supported slab to carry a uniform dead load (excluding self-weight) of 5.75 kPa and a uniform live load of 4.80 KPa. Use fc′ = 21 MPa, fy = 414 MPa, y = 1, and the ACI Code limitations. Design a 3.66 m simply supported slab to carry a uniform dead load (excluding self-weight) of 5.75 kPa and a uniform live load of 4.80 KPa. Use fc' = 21 MPa, fy = 414 MPa, 2 = 1, and theACI Code limitations.

Answered: Image /qna-images/answer/43d5a559-e956-4287-a0e3-278829d53f20.jpg

ASAP NEED IN 1 HOUR I'LL GIVE UPVOTE Design a 3.66 m simply supported slab to carry a uniform dead load (excluding self-weight) of 5.75 kPa and a uniform live load of 4.80 KPa. Use fc′ = 21 MPa, fy = 414 MPa, y = 1, and the ACI Code limitations.

ASAP NEED IN 1 HOUR I'LL GIVE UPVOTE Design a 3.66 m simply supported slab to carry a uniform dead load (excluding self-weight) of 5.75 kPa and a uniform live load of 4.80 KPa. Use fc′ = 21 MPa, fy = 414 MPa, y = 1, and the ACI Code limitations.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1 A column is supporting a flat slab with a tributary area of 10m × 8m. The slab is 220mm thick. The column has a 2000mm × 2000mm × 250mm deep (excluding slab thickness) drop panel. Assuming a 0.75 kPa superimposed dead load and a 1.5 kPa uniformly distributed imposed load Q on the flat slab, what is the ultimate design load on the top of the column in kN?
A 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 145 kN/m and service live load of 215 kN/m. The base of the wall footing slab is 1.0 m from the ground surface. Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 200 kPa, f’c = 28 MPa and fy = 420 MPa. calculate the spacing of 12-mm-diameter rebars for flexure.
300 mm thick footing slab supports a 300 mm thick wall carrying uniform service dead load of 214.31 kN/m and service live load of 145.9 kN/m. The base of the wall footing slab is 1.2 m from the ground surface.Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 215.46 kPa, f’c = 27 MPa and fy = 420MPa. 1.Calculate the net allowable bearing capacity of soil in kPa. 2.Calculate the minimum required width of the wall footing slab. 3 Calculate the maximum ultimate moment (kNm) in the slab if the width of footing slab is 2.1 m 4 Calculate the required center to center spacing of 16 mm bars for flexure if the maximum factored moment in thr slab is 75 kN-m 5 Calculate the ultimate beam shear stress on the footing slab if the footing slab is 2.1 m wide.
A 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 215 kN/m and service live load of 145 kN/m. The base of the wall footing slab is 1.0 m from the ground surface. Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 200 kPa, f’c = 28 MPa and fy = 420 MPa. alculate the effective net soil bearing capacity of the soil. = kPa (one decimal place)
A proposed column has the following design loads:Axial load: PD = 200 k, PL = 170 k, PE = 50 k, PW = 60 k (all compression)Shear load: PD = 0, PL = 0, PE = 40 k, PW = 48 kCompute the design axial and shear loads for foundation design using ASD.
A proposed column has the following design loads:Axial load: PD = 1,100 kN, PL = 750kN, PE = 200 kN, PW = 250 kN (all compression)Shear load: PD = 0, PL = 0, PE = 175 k, PW = 220 kCompute the design axial and shear loads for foundation design using ASD.
A 320 mm thick footing slab supports a 300 mm thick wall carrying uniform service dead load of 235.5 kN/m and service live load of 124.3 kN/m. The base of the wall footing slab is 1.4 m from the ground surface. Use 16 mm diameter for main bars. Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 231 kPa, f’c = 27 MPa and fy = 414 MPa. Calculate the allowable nominal beam shear stress in MPa. Express your answer in 3 decimal places.
Given a simply supported reinforced concrete slab with the effective span lo=2.8 m. The slab is 90 mm thick and reinforced by $10@200 longitudinal bars. The material properties are f= 11.9 N/mm², f= 1.6 N/mm². fy=280 N/mm, and E, = 2.0 x 10 N/mm². Calculate the maximum load (per square meter) that the slab can sustain.
a 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 214.31 kN/m and service live load of 145.94 kN/m. the base of the wall footing slab is 1.2 m from the ground surface. design parameters are as follows: ysoil = 16 kN/m^3, yconci = 24 kN/m^3. qa = 215.46 kPa. f'c = 27 MPa and fy = 420 MPa. 1. calculate the net allowble bearing capacity of soil in kPa. a. 192.17 b. 189.06 c. 117.32 d. 176.26 2. calculate the minimum required width of the wall footing slab. a. 1.9 m b. 2 m c. 1.8 m d. 1.7 m 3. calculate the maxium ultimate moment (kN.m) in the slab if the width of the footing slab is 2.1 m. a. 82.64 b. 94.63 c. 128.80 d. 111.32
A 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 145 kN/m and service live load of 215 kN/m. The base of the wall footing slab is 1.0 m from the ground surface. Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 200 kPa, f’c = 28 MPa and fy = 420 MPa. 22. Calculate the effective net soil bearing capacity of the soil. = [q] kPa (one decimal place)
A wall footing is used to support a 300 mm. reinforced concrete wall carrying a dead load of 292 kN/m and a live load of 220 kN/m. The footing has a total thickness of 450 mm. with a steel covering of 75 mm. The bottom of the footing is 1.2 m. below the final ground surface. Allowable soil pressure is 199.70 kPa. Weight of soil is 15.7 kN/m3. fc' = 27.6 MPa. fy = 276.5 MPa. Weight of concrete is 23.5 kN/m3 2. Which of the following gives the nominal shear stress of the footing
A square footing 2.4 m x 2.4 m x 0.45 m thick supports a 300 mm square column at its center. Column loads are at service conditions DL = 326 KN, LL = 219 KN, fc' = 21 MPa, and fy = 415 MPa. Concrete cover to the centroid of steel reinforcement is 100 mm. Calculate the nominal one way shear stress in the slab