Answered: Assignment 20 Determine the reaction of…

Engineering

Mechanical Engineering

Assignment 20 Determine the reaction of the supports.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Related questions

Q: Problem 5.48 The tension in cable BC is 100 lb. Determine the reactions at the built-in support. 6…

A: Given data: Tension in cable, BC = 100 lb Determine the reaction at the built-in support = ? The FBD…

Q: Compute the total reactions at A and B for the truss show. E G 300 kN 10m C A F H 5m 5m 10m 10m 600…

Q: Determine the horizontal and vertical components of reaction at pin A and the reaction on the beam…

A: Given: To determine: Reaction force at A and C

Q: Determine the force in member BD and the components of the reaction at C.

A: Given data To determine the froce in BD and reactions at C

Q: Determine support reaction

A: Introduction : The given structure is known as truss structure . It consist of two support one…

Q: Determine the magnitude of the reactions that occur in the support of each of the following…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Using the given frame, find the vertical and horizontal reaction at support A. (kN) 30 kN/m 50 kN 1.…

Q: Determine the reactions at A and B and the load required Q to hold bar AB in a horizontal position…

Q: Calculate the support reactions at A and B for the loaded beam. 96 lb/ft B 2.1 5.7' 74 lb

A: Convert the uniformly varying load into point load, F=12×5.7 ft×96 lb/ft=273.6 lb Calculate the…

Q: For the shown truss, the vertical support reaction at A equals

A: Always start by calculaing the reaction at the node . Solve the truss by taking the sum of forces =…

Q: Б

A: introduction: here we have to find out reaction

Q: Problem Set: 8. The frame is used to support a 50-lb load as shown in the figure, determine; (Use…

Q: P А B Q А, A, A, B. M B, A, B, A, B, в, (а) (b) (с) (d)

A: Option b is correct.

Q: Solved Determine the reaction forces at the supports A and B

Q: · For the frame and loading shown, determine the reactions at A and D, and the force at pin B (Note…

Q: Calculate the support reactions, calculate internal forces on the designated section C.

Q: A simple beam supports two concentrated loads and a uniformly distributed load over 8 m of the span.…

A: Consider the free-body diagram of the beam as shown below.

Q: The two beams are connected by a joint at point C and loaded by a constant distributed load.…

Q: Loaded truss supported by pin joint at A and by cable at B. B

Q: -15. Determine the reactions at the supports. 5 kN 2 m 6 kN 8 kN 2 m 2 m 2 m

Q: 4.) Calculate the pin reactions at A, B, and C for the system shown. Assume all structural members…

Q: Determine the support reactions and draw the SFD and BMD for the following frame. 5 kNim

Q: 2- Determine the support reactions and tilt in the beam after loading. Assume the beam is…

Q: 20 kN 30 KN 40 kN 6 m

Q: 6. The beam is supported and loaded as shown. Determine the reactions at hinge A and roller B. 100…

Q: Q4: For the frame shown in Fig.(4), determine the components of reaction at pin C

A: Given

Q: 30 kip 5 kip/ft

A: To determine the support reaction at B we will first draw the free body diagram.

Q: Determine the reactions at the beam supports for the given loading.

A: Total reaction of uniform loading, R1 = 200 x 15 = 3000 lb total reaction of distributed loading, R2…

Q: For the beam shown below: Draw the free body diagram showing the reactions for each type of…

A: For roller support only vertical reaction. For pin support horizontal reaction and vertical…

Q: The truss is affected by load F on joint “G" and load P on joint "F". The loaded truss is supported…

Q: Use the method of sections to find the true magnitude and direction in bar DB of the truss. Hint…

Q: Identify the zero-force members in the trusses below A

A: The condition for the force to be zero in a member of a truss is: " If three forces act at a joint…

Q: 3rd QUESTION Determine the reaction forces force of the loaded truss. 10 kN 45% b C a

A: Given

Q: The truss is affected by load F on joint "G" and load P on joint "F". The loaded truss is supported…

A: Joint B has two non-collinear members (AB & BC) and no external load acting at B, therefore AB…

Q: Determine the reaction at the support A of the frame. Supply the answer in kips (1000 Ibs).

Q: The truss is supported by a pin at A and a roller at B. Determine the suppor The truss is supported…

Q: A Beam is supported by a pin A and cable Bc ar b. The horizontal component of four reaction at pin A…

Q: In each case, calculate the support reactions forces and then draw the free-body diagrams of joints…

A: Consider the free body diagram for the system.

Q: ate the reactions at A and B for the beam shown.

Q: Determine vertical pinned support reaction

A: Given data : Point load =8 KN Point load=8 KN Point load=8 KN Point load=16 KN To find : Vertical…

Q: Calculate the reactions at A and B for the beam shown. Neglect the weight of the beam. 6 kips 7 kips…

A: To calculate the reactions at supports.

Q: Determine Ax, Ay and NB, i.e. the horizontal and vertical components of reaction of the pin A and…

Q: If F = 4 kN and P7 kN , compute the magnitude of the reactions at the fixed support at A

Q: Problem 4: Determine the normal reaction (in kN) of the roller at B and hinge reactions at A for…

Q: Problem 2 Determine the reaction for the given support in the truss as shown in Figure 2.0. All…

Q: ) Determine the support reactions for the depicted frame. Given: a = 30.

Q: 4 kN 3 m 4 m Use the method of joints to find all reaction and member forces in the trusses.

Q: Determining the reactions and forces of the members DE, the following truss.

Question

MAHAINE T. ECHAVEZ
BSCE
17-0250
Assignment 20
Determine the reaction of the supports.
3 kN
2.5 kN 1.5 kN a0
B
2 m
4 m
* 2m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Prior to the application of the P = 120 kip load, the gap between C and the rigid wall at D was as depicted as below. Determine the support reaction at D (in kip) after force P has been applied. The assembly is made of solid cylinders: AB is Stainless 304 steel alloy, and BC is 6061-T6 aluminum alloy.
. R e« o - o, . gxample 16.1. A solid round bar 60 mm in diameter and 2.5 m long is used as a strut. One of the strut is fixed, while its other end is hinged. Find the safe compressive load for this strut, ing Euler’s formula. Assume E = 200 GN/m? and factor of safety = 3. s T e
A steel rod is acted upon by the loading shown below. 50 mm2is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa.
The strut is supported by a pin at C and an A-36 steel (Young’s Modulus is 200 GPa) guy wire AB. If the wire has a diameter of 5 mm, determine how much it stretches when the distributed load acts on the strut. W0=11Kn/m
Three steel rods (E = 200 GPa) supports a 50 kNload P. Each of the rods AB and CD has a 300 mm2cross-sectional area and rod EF has a 600 mm2cross-sectional area.(a) State whether the structure isstatically determinate or indeterminate.Why?(b)Determine the force and thestress in each rod.(c) Determine the deformation of each rod.Note: The link BED is rigid, and BE = ED.
The load is supported by the four stainless steels wires that are connected to the rigid members AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 16mm2. Given that E= 200Gpa for all the steel wires. a) Draw Freee Body Diagram(FBD) of each rigid member. b) Determine the angle of tilt of each member after the 2250N load is applied
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed. Kindly Use NSCP 2015 please for this problemHint Answers: 1,420.18
The brass tube AB (E = 105 GPa) has a cross-sectional areaof 138 mm² and is fitted with a plug at A. The tube is attached atB to a rigid plate that is itself attached at C to the bottom of analuminum cylinder (E = 70 GPa) with a cross-sectional areaof 250 mm². The cylinder is then hung from a support at D. In orderto close the cylinder, the plug must move down through 1.2 mm. Determine the force P that must be applied to the cylinder.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed.Hint Answers: 1,420.18
other given: T(sub B) = 80.11 T = 5.67 kN-m