Answered: Assume that a voice channel occupies a…

Assume that a voice channel occupies a bandwidth of 8 kHz. We need to multiplex 10 voice channels with guard bands of 1000 Hz using FDM. Calculate the required bandwidth.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 7RQ

See similar textbooks

Related questions

Q: 22: In PSK system the bit rate of NRZ stream is 20 Mbps and carrier frequency is 2GHZ. Find the…

A: Answer is given below-

Q: Q3: A 100 Mbps link between video server and a client is established. If receiving video frames of…

A: Given Latency = 1.1 sec, Bandwidth = 100 Mbps, Frame size = 13.5 MB, speed of light = 2.8 * 108…

Q: I A channel has a frequency range between 3 KHz and 14 KHz. The SNR in this channel is 25 dB. Find…

Q: Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in…

A: Bit rate is the transmission of a number of bits per second. The Baud rate is defined as the number…

Q: 1. each UE-1 and UE-2 when equal bandwidth (OMA schemes) 2. each UE-1 and UE-2 when the user is…

A: NOMA (Non orthogonal multiple access):- It has higher spectral efficiency as compared to OMA. Has…

Q: Computer Science A cellular network is designed to achieve a maximum data rate of 1 Gbps in the…

A: Packet transmission is crucial to a network's ability to provide services. People expect their…

Q: Calculate the peak LTE OFDMA downlink throughput of 5-MHz channel bandwidth with 512QAM and 2x2 MIMO

A: No of Subcarriers for 5-MHz channel bandwidth = 300. Also, for 512QAM = 29 so, 9 bits is required…

Q: A channel has a bit rate of 4 kbps and a propaga tion delay of 20 msec. For what range of frame…

A: The Answer is

Q: HDLC (High-level Data Link Control) is a group of protocols or rules for transmitting data between…

A: It is defined as High-level Data Link Control (HDLC) which is known as a group of communication…

Q: . What is the theoretical capacity of a channel for the following case? Bandwidth = 1…

A: What is the theoretical capacity of a channel for the following case? Bandwidth =1MHz SNRdB=20

Q: Why is it essential that a certain bandwidth be maintained? Could you please explain?

A: Why is it essential that a certain bandwidth be maintained? Could you please explain answer in below…

Q: Question 22: A channel, whose bandwidth is 3 MHz, has an intended capacity of 20 Mbps, Assuming…

A: Introduction

Q: the length of cable through which a signal can be sent before its power decreases to half the…

A: here we are given the attenuation values for three type of transmission cable and we need to find…

Q: Direct Sequence Spread Spectrum (DS-SS) is widely used secure wireless communications. Assume you…

A: It is mainly used for secure wireless communications.As wireless are used most ,because wired…

Q: What is Bandwidth when it comes to data transmission?

A: Introduction: The highest rate of data transfer for a network or internet connection is called…

Q: we use synchronous TDM and combine 20 digital sources, each of 100 Kbps. what will be the minimum…

A: It is defined as a multiplexing technique by which multiple data signals can be transmitted over a…

Q: Calculate the length of cable through which a signal can be sent before its power decreases to half…

A: Here we are given the attenuation values for three type of transmission cable and we need to find…

Q: Transmissions can be secured by expanding the bandwidth of a channel and adding redundancy, this…

A: Transmissions can be secured by expanding the bandwidth of a channel and adding redundancy, this…

Q: Assume that data rate for each input connection in figure above is 5 Mbps. A unit is 1 bit Find the…

A: 5C) Duration of time slot is given as 1/5 of the bits before they are multiplexed together = 1/5…

Q: The designers of ADSL have divided the available bandwidth in to a. local loop evenly b. local loop…

A: ADSL(Asymmetric Digital Subscriber Line) is a type broadband connection which works through the…

Q: Assume having a low-pass noiseless channel that spans from a Frequency of 0Hz to 130Hz, to send at a…

A: please upvote for my efforts thanks! answer: bit rate= 2* bandwidth * log2(number of levels)

Q: We cannot send the digital signal directly to the channel, when the channel is a. bandpass b.…

A: There is a multiple choice question given. The digital signal can not be sent directly, when the…

Q: 1- In 5G network we use Ultra High Definition quality for video and Suppose that it is to be…

A: Given : Resolution = 2160 * 3840 Total intensity values = 64 Sending rate of picture = 30 pictures…

Q: Assume that a voice channel occupies a bandwidth of 4 kHz. We need to combine three voice channels…

A: Answer is given below

Q: d) How much time is required to download a document of 1Gb if the data rate of the channel is X bps…

A: In this question, we have to calculate the required time to download a document of 1Gb. Time…

Q: MIMO and frame aggregation are techniques used in recent Wi-Fi standards for increasing capacity.…

A: A wireless access point is an essential component of a Wi-Fi ad-hoc network.(TRUE) Because the…

Q: 2. (a) A signal travels from BRAC University to your home. At BRAC University, the signal power is…

A: Given: Power at BRAC univeristy=1.2kW = 1.2 * 1000 W =1200 W Power at home =106mW = 106 * 0.001 W…

Q: The greater the bandwidth of a given medium, the ________ is the data transfer rate higher lower…

A: Start: The transmission rate of data is determined by the bandwidth of the signals being used.…

Q: the signal is going through a 1.2 MHz Bandwidth Channel, what will be the maximum bit rate that can…

A: Here have to determine maximum bit rate that can be achieved in this channel.

Q: Baseband transmission of a digital signal is possible only if we have a ____ channel. a. low-pass b.…

A: Baseband Transmission of a digital signal is a type of signaling technology that sends digital…

Q: A common measure of transmission for digital data is the baud rate, defined as the number of bits…

A: The Answer is

Q: Five channels, each with a l00 kHz bandwidth, are to be multiplexed together. What is the minimum…

A: Five channels, each with a l00 kHz bandwidth, are to be multiplexed together the minimum bandwidth…

Q: A CSMA/CD LAN has minimum frame size 100 bytes and is running at 100 Mbps. The signal speed in the…

Q: No need explanation just ans it... The research and development department at your office has been…

A: INTODUCTION THE QUESTION IS ABOUT use of a broadband network versus a based band network and here…

Q: Assume having a low-pass noiseless channel that spans from a Frequency of OHz to 180HZ, to send at a…

A: please do upvote for my efforts ! answer: bit rate = 2* bandwidth * log2(number of levels)

Q: WIFI OFDM You are tasked with designing a new OFDM WIFI with the following specifications Symbol…

A: OFDM is a method in which the frequencies are placed, and the wireless points differentiate data…

Q: Q3. A line has a signal-to-noise ratio of 2000 and a bandwidth of 12000 KHz. What is the maximum…

A: The maximum data rate supported by this line: C=W log2(S/N+1)

Q: Four channels, two with a bit rate of 200 kbps and two with a bit rate of 150 kbps, are to be…

A: Firstly here giving four channels Two with a bit rate of 200 kbps Two with a bit rate of 150 kbps…

Q: The minimum time required to download one million bytes of information for V32 modem would be a. 800…

A: Answer is b) 834s

Q: n rule, determine the system bandwidth that can transmitted imum bit rate of 10 Gbps when the signal…

Q: channel has a 1-MHz bandwidth. The SNR for this channel is 63. What is the appropriate signel level?

A: A channel has a 1-MHz bandwidth. The SNR for this channel is 63. What is the appropriate signal…

Q: requires that each station first listen to the medium before sending. MA CSMA FDMA CDMA

A: Ans:) MA stands for multiple access. it is the use of multiplexing techniques to provide…

Q: Transmissions can be secured by expanding the bandwidth of a channel and adding redundancy, this…

A: The Forward Error Correction is a method of adding redundant data to a signal to make it secure and…

Q: Computer Science Describe the capabilities and bandwidth efficiency of codes in terms of their…

A: 1. Bandwidth : Bandwidth is defined as the potential of the data that is to be transferred in a…

Q: A channel has a 100 khz bandwidth. Its SNR is 31; what is the appropriate bit rate a. 4 Mbps b. 3…

A: Your answer is given below in detail. Concept :- The capacity of band-limited AWGN channel is…

Q: Question 38 Group delay variation (GDV) affects which types of modulation the most? BPSK O QPSK 256…

Q: Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in…

A: Answer is given below .

Q: Three client channels, one with a bits of 200 Kbps, 400 Kbps and 800 Kt ps are to be multiplexed a)…

A: We can allocate one slot to the first client channel and one slot to second client channel and one…

Concept explainers

Transmission media

A communication channel that transmits data from a source to a recipient is referred to as "transmission media." Electromagnetic impulses are used to transmit data. Transmission media's primary purpose is to transmit data in the form of bits via a local area network (LAN). In data transport, it is the physical link that connects the transmitter and receiver. Transmission medium is part of layer 1 or physical layer of the ISO/OSI (Open System Interconnection) model.

Question

Q1) Sec a) Assume that a voice channel occupies a bandwidth of 8 kHz. We need to multiplex 10 voice channels with guard bands of 1000 Hz using FDM. Calculate the required bandwidth.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

CSE Subject:- img processing A common measure of transmission for digital data is the baud rate, defined as the number of bits transmitted per second. Generally, transmission is accomplished in packets consisting of starting bit, a byte of information and a stop bit. Using this approach, answer the following. (a) How many minutes would it take to transmit a 512 x 512 image with 128 gray levels at 300 baud?
Calculate the total number of bits used in downloading a 50 MB video file. Also calculate the time (in minutes) it takes to download the same video file, if the download link is a telephone line with 9600 baud rate. Assume 8 - bits of data per character, 1 start bit, 1 - stop bit, and 1 parity bit.
TDM, FDM, and CDM are physical layer multiplexers.Please list each approach's pros and cons.
Compare TDM, WDM, AND FDM
-. Write the procedures of active and passive scanning in IEEE 802.11 -. Write the procedure of hand-off in wireless local area network -. Write when a wireless station goes to a doze state to save its power.
The greater the bandwidth of a given medium, the ________ is the data transfer rate higher lower both a and b neither a nor b
Multiple Choice Questions: 2) Data transfer rate is often measured in Mbps Kbps Bps gbps
1- The bandwidth of the 8 PSK is .......... the bandwidth of the PSK
FDM and TDM are used in communication to _______________ Increase the bandwidth of the path Reduce error in signals Increase the strength of the signal Effectively use the available bandwidth
Assume that a voice channel occupies a bandwidth of 8 kHz. We need to multiplex 10 voice channels with guard bands of 1000 Hz using FDM. Calculate the required bandwidth
6. A replacement section of cable will usually have extra _______ in the cable.A. insertion lossB. attenuationC. channelsD. slack
Assume having a low-pass noiseless channel that spans from a Frequency of 0Hz to 130Hz, to send at a bit-rate value that is not less than 1Kbps, then you would at least need ................. signal levels.