Assuming that the beam section has cracked, determine the momentcapacity of the beam section below using transformed area method.Use fc¹= 28 Mpa, fs = 135 Mpa, n = 11. The beam is reinforced with 3-25mm diameter bars with 60mm effective cover.009100400100100400200000100

Given-A cracked beam reinforced with three bars of 25mm diameter. Required- to calculate moment…

Assuming that the beam section has cracked, determine the moment capacity of the beam section below using transformed area method. Use fc'= 28 Mpa, fs = 135 Mpa, n = 11. The beam is reinforced with 3- 25mm diameter bars with 60mm effective cover.

Assuming that the beam section has cracked, determine the moment capacity of the beam section below using transformed area method. Use fc'= 28 Mpa, fs = 135 Mpa, n = 11. The beam is reinforced with 3- 25mm diameter bars with 60mm effective cover.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ++ 0.3 m S2 3.15 m ++ 0.3 m B. 7.0 m ++ 0.3 m 1.2 m 0.3 m 4.2 m 0.3 m 1.4 m 300 mm #+ +1 140 mn 360…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A girder of a highway bridge has a total span length of 15 meters, overhangs 2.5 meters from the…

A: influence line diagram: here we are using Muller Breslau principle , according to this principle…

Q: Create a graph that shows the acceleration due to gravity as a function of distance from the earth’s…

A: The acceleration due to gravity can be expressed as a function of distance from the earth’s surface.

Q: The force in AD

A: Given, A truss Free body diagram:-

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface based on Boussinesq's…

A: Given data: A uniformly distributed line load of 500 kN/m. The ratio of vertical stress at a depth 2…

Q: Four measurements of distance were recorded as 352.45, 352.04, 351.89, and 353.12 meters and given…

A: Given:Measurements:X1=352.45 with W1=2X2=352.04 with W2=5X3=351.89 with W3=1X4=353.12 with W4=8

Q: The relation between speed u (in km/h) and density k (number of vehicles / km) for a traffic stream…

A: Given- u=70-0.7k where, u=speed in kmph. k=traffic density (no. of vehicles/km). It is needed to…

Q: The performance function for a highway connecting a suburb with the business district can be…

Q: Two steel spheres of diameters d, and d, where d₂= 2d,, are dropped from rest at the free surface of…

Q: Compute/Derived the following: a. wall shear b. wall moment c. Reaction

A: "Since you have posted a question with multiples subparts we will solve first three for you .To…

Q: All the parts please! Thank you!

A: Given: vriver=16msmTotal=850 Kg After 12 seconds boat and river drift at same velocity. Within 3…

Q: Problem 1. Calculate the area between the offsets using Simpson's One-Third Rule. Chainage (m) 0…

Q: The demand in a water distribution system averages 15 cfs. What is the total annual demand in acre…

Q: 2m jokN 2m 25kN ļ 2m Fa solve for maximum Reflection using Double-Integration

A: Let,RA=Vertical reaction at support A in upward direction.RB=Vertical reaction at support B in…

Q: The absolute maximum shear stress in the member

A: Given data, Solid circular torsional member OPQ is subjected to torsionalmoments as shown in figure.…

Q: What will be the nature of surface of pipe if the flow of water is taking place having roughness…

A: Given data: Roughness size, k=0.10 mm Average shear stress at pie boundary, τo=250 Nm2 v=10-6 m2sec

Q: A freshly cut log floats with 2/3 of its volume protruding above the water surface. a) Determine the…

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A: Given data: Chainage (m) 0 25 50 75 100 125 150 Offset (m) 0 5.49 9.14 8.53 10.67 12.5 9.75…

Q: Prob.5. Samples of a dry sand are to be tested in triaxial and direct shear test. In the triaxial…

A: Given, Major principle stress, σ1 = 960kN/m2 Minor principle stress,σ3 = 260kN/m² Normal stress=…

Q: What if any materials options do we have for graphene coating in construction? Do these options…

A: This type of coating is used to enhance the property of the steel. Thus the strength of the steel…

Q: n = Gs= Saturation =

A: n = porosity it ranges from 0 to 100 % Gs = specific gravity e = void ratio ρ = density of soil γ =…

Q: Q3) leveling staff setup on a BM of elevation of 89.90 m is observed from point A where the three…

Q: ually spaced vertical rods in Fig. (a) are securely attached to a rigid ho er rods are made of an…

A: Given:- σyp=330MPaE=70GPaE=200GPaσyp=290MPaTo find:-residual stresses

Q: answer c

A: a=15min b=0.005min/veh-hr c=6000veh/hr d=150veh/hr/min

Q: The homogeneous 100 N body A of figure shown is in equilibrium and rests upon the smooth cylindrical…

Q: draw C1-300x300 mm with 8-D16 mm vertbars and 10 mm lateral ties spaced 2 @50 mm, 4@100 mm and rest…

A: Drawing C1: Reinforcement details

Q: A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the…

A: Given- Heads= 55.2 m & 34.1 mk=80 m/dayporosity n=0.25time taken to reach from P to Q is needed…

Q: ET Find the tensile stress Jab in cable AB

A: Given data :

Q: Using suitable examples, discuss the difference between the Static efficiency and the Dynamic…

A: Static efficiency and dynamic efficiency are two names for the same thing. Dynamic efficiency allows…

Q: 2. A 100 m tape is suspended at the ends under a pull of 15 kg. It has also supports at 30 m and 75…

Q: Who proposed drawings with multiple views rather than the commonly used pictorial drawings?

A: In ancient times, any drawings were read using one face view. In later times, in order to avoid…

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

A: Given: Shaft dimensions Torque Yield shear strength To find: Absolute maximum shear stress in…

Q: A smooth flat plate is in a parallel flow stream. The ratio of the drag over the upstream half of…

Q: N. Draw a free body

Q: B-Unequal-Tangent Parabolic (Vertical) Curve: Example: A grade g1 of -2% intersects g2 of +1.6% at a…

A: Solution: Point A STA 85 + 00: Elev. = 743.24+2(2) = 747.24' Point B STA 90 + 00: Elev. =…

Q: 1. A built up steel beam uses a W18x97 on its top and with a 1"x32" vertical plate and a 2"x16"…

A: Properties of the given sections: For W18x71: A=20.9 in2d=18.5 intw=7.64 intf=0.81 inIx=1170…

Q: A 25 cm diameter pipe carries a (p=1.22kg/m³) (v=1.5x10-5m²/sec) at a average velocity of 8.0 m/sec.…

Q: A beam with a span of 7.0 m between supports has an overhanging extended part of 2.0 m on one side…

A: Given: DL = 30 kN/m LL = 18 kN/m Factored load: Wu=1.2DL+1.6LL=1.230+0.618Wu=64.8 kN/m

Q: PROBLEM: Prove that the truss shown is statically determinate and solve for the force members. State…

Q: Water flows around the vertical two-dimensional bend with circular streamlines and constant velocity…

A: Given data Water flows around bend having constant velocity. The pressure is 63 kPa We are asked to…

Q: tion. The tie rod is connected at B and C by 20-mm-diamet h of 220 MPa, and each of the pins has an…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Problem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is…

A: Flexural stress The tensile strength of concrete beams or slabs is measured in terms of flexural…

Q: A steel column of ISHB 350 @72.4 kg/m is subjected to a factored axial compressive load of 2000 kN.…

A: Given- ISHB 350 @ 72.4 kg/m,factored load=2000 kN,M20 concrete, It is needed to find the length of…

Q: Problem. A SRCB is subjected to loads as shown. Required: Adequacy of the SRCB against flexure…

A: Given data: ABCD=1163 Singly reinforced concrete beam with, Dead load=2A=21 kN/m Live load=3B=31…

Q: Select the answer that most nearly gives the axial force on member ad from the real structure in…

A: The given figure is shown below:

Q: ERBsent out six groups of students to measure a distance between two points on the ground. The…

A: The measured value of the distance between the two station - X1 = 360.52m X2 = 360.35m X3 = 360.89m…

Q: Problem 4. Replace the three forces acting on the plate by a wrench. Specify the magnitude of the…

A: Given :

Q: Complete solution. Double Integration El = constant fordy 20 KN 18 kN/m Find the slope @ B,…

A: Let,RA=Vertical reaction at support A in upward direction.RB=Vertical reaction at support B in…

Q: Problem 5 Specific Gravity (Gs) Saturation Water content 2.66 100% 49% e = n = Y = % lb/ft³

A: Reference : Soil Mechanics. Void ratio is given by ; S × e = w × G e = wGS Where ; S = Saturation =…

Q: thank

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

100%

Assuming that the beam section has cracked, determine the moment
capacity of the beam section below using transformed area method.
Use fc¹= 28 Mpa, fs = 135 Mpa, n = 11. The beam is reinforced with 3-
25mm diameter bars with 60mm effective cover.
009
100
400
100
100
400
200
000
100

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Analyze the frame using slope deflection method (at least five cycles) for end moments. Then draw the PVM diagrams for member BC.
Calculate the value of the deflection at point B due to uniformly distributed load w in the form answer in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI: Use the conjugate beam method (Moment-area Method) to obtain the slope (Slope) after the deformation of point A and the vertical displacement (Deflection) of point C *The correct answer is 24 kN-m2/EI clockwise and 58.7 kN-m3 /EI down, but I need to calculate steps, thanks
Consider that a box section is used for the beam loaded as shown in figure. Using flexure and shear stress formula, determine the Moment of inertia of the beam about centroidal x-axis in *10^6 mm*. a=6m b=3.2m c=344mm d=50mm
For the beam loaded as shown in the figure 1, determine the deflection at B in mm using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. a = 3.9 m, b = 9 kN/m, c = 15 kN.
PLEASE ANSWER ASAP AND REFER TO THE GIVEN VALUES BELOW. Use Slope-Deflection Melhod to solve for the moment at beam BC. Mec in kN-m on the 250 mm x350 mm beam shown in the figure below. Assume E = 80 GPa and use a = 2.0 m, b = 3.4 m. c = 41 kN and d = 46 kN/m
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1. Determine the moment of inertia of the cross section .2. Determine the slope at point B
what is the value of moment MD when x = 13 m due to a unit load? Use four decimal places.
2) use Maccaullay method to determine the slope and deflection at 2 m from point A due to the imposed load as shown in Figure Q2. The beam cross section is T, shape with flange width of 150 mm and flange thickness of 10 mm and web height of 120 mm with thickness 8mm. E = 200 GPa
Given the figure below. Use UNIT LOAD METHOD in determining the maximum deflection at midspan. E and I are constant. 1. In solving the maximum deflection at midspan, how many portions or segments must the beam be divided so that the real and virtual loadings are continuous in each segment?2. Consider segment AB of the real beam, with x measured from A, what is the moment equation M_(AB ) ?3. (In solving the maximum deflection at midspan, how many portions or segments must the beam be divided so that the real and virtual loadings are continuous in each segment?) in this question, what are the limiting values of x?
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI: Use the conjugate beam method (Conjugate Beam Method) to obtain the slope (Slope) after the deformation of point A and the vertical displacement (Deflection) of point C *The correct answer is 24 kN-m2/EI clockwise and 58.7 kN-m3 /EI down, but I need to calculate steps, thanks
Determine the internal moments at the supports of the beam shown using: 1.) ThreeMoment equation 2.) Moment Distribution Method 3.) Slope-Deflection Method Pick two method only Given: E=200GPa I=20x10^6 mm^4 w=8kN/m L1=10m L2=8m