At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 80 MPa, oy = 35 MPa, and Txy = 84 MPa, acting in the directions shown in the figure. oy Ox At this point, determine the strain components &x, Ey, Ez, and xy. Assume that E = 69 GPa and v = 0.29 for the machine component. Txy

Q: d on this curve? What speed should be posted if 8kph increments are used?

A: FInd the Stopping sight distance S=NL24.4S=4.4+4.41008224.4S=134.48>Lusing another equation…

Q: securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a…

A:

Q: 05: For the given state of stresses shown, draw the required Mohr's circle and determine: The…

A:

Q: (c) A circular cylinder is rotated about its own axis at a constant rate of 1500 rpm Determine the…

A: Given, Number of rotations in 1 minute (60seconds) , N= 1500 radial distance r = 15 cm = 0.15 cm…

Q: DRAW the shear and moment diagram of the following beams. What is the maximum shear (both negative…

A: Given  A beam with loadings  Required  Maximum positive and negative shear force and bending moment…

Q: Problem Set 3: The overhanging beam carries a uniformly distributed load totaling 8W and two…

A:

Q: Derive the response relation for each of the models shown in Figure P1.25 assuming that the force F…

A: To find:- derive the response for model

Q: 3- A 14ft braced column is subjected to DL-280k and LL-235k. Design and choose the lightest WT shape…

A: Pu = 1.2*280 + 1.6*235 = 712kip  fy = 50 ksi. E = 29000 ksi

Q: Three turbines each of capacity 10000 kW are installed at a hydel power station. If the peak load…

A: Given data, No. Of turbines = 3 Capacity of Each turbine= 10000kW Peak load = 25000kW Average load =…

Q: What is the equivalent line load that beam B2 will carry from the loads in Area 1? a. 10.6 KN/m b.…

A:

Q: Describe the pre-design studies carried out and types of information collected for a given…

A: The conceptual design phase is widely regarded to become the start of the design process. It's…

Q: Draw the influence lines for the force in member GC of the bridge truss. H G 6m -6 m- B -6 m (a) 6…

A:

Q: The total irrigation depth of water, required by a certain crop in its entire growing period of 120…

A:

Q: √ plity, experiencing torque while member X-Z is only experiencing flexure. What should be the…

A:

Q: simple curve having a radius of 230 m have tangents with with central angle equal to 50° The…

A:

Q: 3. For the beam shown below, fy 60,000 psi and fe' = 4,000 psi. Determine if the compression steel…

A: Given values: fy= 60000 psi f'c= 4000 psi For this concrete,  β1= 0.85  Compression reinforcement: 2…

Q: A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the…

A:

Q: QUESTION 2 Determine the force in members CE, CD and AD and state whether the members are in tension…

A:

Q: Water flows at the rate of 0.003 m3/s in a 100-mm-diameter pipe. Assuming n = 0.025, find the head…

A:

Q: Calculate the value of EIS at point B of the simple supported beam ABC using area-moment method.…

A:

Q: Sketch a typical surface water treatment plant, label all its parts, and explain their functions.

A: Wastewater treatment : Wastewater treatment is the process of removing impurities from wastewater…

Q: Q.12. The velocity distribution in the boundary layer is given by: 3 1 η n² F V 2 2 y In which n=…

A:

Q: st unit weight o sture content is of the soil solids

A:

Q: Calculate the amount of irrigation water for the field.

A: Given:Pan evaporation=100 mmeffective rainfall=20 mmcrop coefficient=0.4irrigation efficiency=0.5

Q: Compute the value of Ely at midspan for the beam loaded shown in fig 500 N 450 N/m A D 2m 2m B 1m

A:

Q: docs.google.com * Given: Maximum shear FORCE=13 KN, and moment of inertia = 120 x 10^6 mm^4. Find…

A:

Q: 5. Determine the suitability of the 203 x 203 x 60 kg/m UC section in $275 steel to resist a design…

A: Given, Fy = 275 MPa P = 1400 kN

Q: A double storey reinforced concrete restaurant will be built near the beach in Batu Layar, Johor.…

A: In this Question , RCC IS 456: 2000 code is used and different tables of this code is used. A/c to…

Q: 6. Three turbines each of capacity 10000 kW are installed at a hydel power station. If the peak load…

A:

Q: Determine the acceleration of the particle moving in a circular path as shown below at t instant…

A: Given:velocity, v=1 m/stangential acceleration, at=2 m/s2

Q: H-W Duse Kennedy equation to design canal for following: S = 2.5 X10 4 n=0.0225 m=0.9 Q = 30 m ³…

A: *Multiple questions*   As per our guidelines we are supposed to answer?️ only one question. Kindly…

Q: Does the column shown in Figure (3) have enough available strength to support the given service…

A:

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A:

Q: Reservoir A, the source of water for towns C and D, is at elevation 200m. The distribution reservoir…

A: Given, f = 0.02 Per capita consumption = 150 L/day

Q: In reference to the figure, WAB В B Given: AB= 10.5 m BC = 8.2 m 0 = 41° ß = 28° Determine the…

A:

Q: 137 inches + 5,048 inches +752 inches

A: To find:- 137 inches + 5,048 inches +752 inches

Q: A township is to treat 5,00,000 litres of sewage per day which has a 5-days BOD of 150 ppm. An…

A:

Q: Explain traffic flow, density, and average speed.

A: These terms are related to traffic engineering.

Q: ble below, Calculate the area enclosed by the traverse. Point X(m) Y(m) 0 0 + 170 + 320 +470 +90…

A: solution  The area of the traverse can be found out using the formula  Area A=1/2∑(Xi(Yi+1-Yi))…

Q: cantilever beam BD rests on a simple beam AC as shown below. Both beams are of the same material and…

A: Given Data:P=1400 lbspan AB=12 ftSpan DB=8m

Q: What is the importance of drawing the orthographic view of an object?

A: Sometimes 3-D drawings  can be used to show the overall design and concept but not often clear or…

Q: In the traverse below, angles measured by theodolite as following: ABC-88°20', BCD-250°15',…

A:

Q: Figure P1.18 shows (i) elastic-perfectly plastic and (ii) elastoplastic with strain hardening…

A: To find:- stress is needed when a.a strain of 0.001 b. a strain of 0.004

Q: Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction…

A:

Q: The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w, as…

A: Calculate the reaction of the beam as follows:

Q: Problem Sets The rectangular wood beam is loaded as shown in the largest allowable magnitude of the…

A: FInd reactions:∑ MC=0RA3-831.5-P2=0RA=12+23P∑ FyRA+RC-83-P=012+23P+RB-83-P=0RC=12+13P

Q: QUESTION 9 When laying masonry units, the order of construction is commonly Olay and level walls…

A: In construction of laying of masonry units there are certain steps and procedure that should be…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Describe the role of time in periodic events.

A: Periodic events are those that take occur at regular intervals of time. The rising of the sun every…

Q: s and H0 = 2m what is the wave height and the a

A: Given-wave period =11sDeep water height =2m water depth =5m angle = 5°

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.