At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 52 MPa (C) and an unknown positive shear stressexist on a horizontal plane. One principal stress at the point is 10 MPa (C). The absolute maximum shear stress at the point has amagnitude of 66 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at thepoint.S₂Answers:0x =Txy =Op2 =iiSxySxMPaMPaMPa

At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 52 MP exist on a horizontal plane. One principal stress at the point is 10 MPa (C). The absolute m magnitude of 66 MPa. Determine the unknown stresses on the horizontal and vertical pla point. S₂ Ţ Answers: 0x = Txy = || i Sxy Sx MPa MPa MPa

At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 52 MP exist on a horizontal plane. One principal stress at the point is 10 MPa (C). The absolute m magnitude of 66 MPa. Determine the unknown stresses on the horizontal and vertical pla point. S₂ Ţ Answers: 0x = Txy = || i Sxy Sx MPa MPa MPa

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in Figure P8.6. Find the vertical stress increase at A.
A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
Determine the magnitude of the maximum in-plane shear stress at point A (in MPa).
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 57 kN/m2. Both stresses are principle stress. (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor principal stress is 2,000 psf compression. (a) Draw the Mohr’s circle for this stress combination. (b) Find the maximum shear stress, and also indicate the value of normal stress acting on this same plane. (c) Determine the values of the normal and shear stresses acting on a plane that is 60° ccw from the major principal plane.
A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the cross section of a short column. Knowing that y = 5 in., determine (a) the stress at point A, (b) the stress at point B, (c) the location of the neutral axis.
At a point in a stressed material, the major principal stress is 80 psi compression and the minor principal stress is 20 psi compression. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on this same plane? (c) Determine the value of the normal and shear stress acting on a plane that is 60° clockwise (cw) from the minor principal plane.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
At a point in a stressed material, the major principal stress is 120 kPa compression and the minor principal stress is 40 kPa compression. (a) Draw the Mohr’s circle for this stress combination. (b) Determine the maximum shear stress. Also indicate the normal stress on the plane where shear is a maximum. (c) Determine the value of normal and shear stress acting on the plane 30° counterclockwise (ccw) from the major principal plane.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
For the state of stress shown in the figure. a. Determine the maximum and minimum principal stresses.b. Describe the location of the maximum principal stress from side BC.c. Describe the location of the maximum principal stress from side BD.d. Determine the maximum shear stress.e. Determine the normal and shear stresses at plane AB. A = 30 ,B = 50 , C = 10 ,D = 37