data:Ea = +800µ,Ep = +960µ,Ec = +800Determineb) maximum shear strain (Ymax)Gage cGage bGage a

Answered: Image /qna-images/answer/3ef881df-0537-4c9a-8899-2f8618811388.jpg

At a point on the free surface of an aluminum alloy (E = 10) x 10" psi and v = 1/3) machine component, the three strain gages shown in Figure below were used to obtain the following strain data: Ea = +800, Ep = +960µ, Ec = +800u Determine a) the three principal strains (E1, E2, amd E3) b) maximum shear strain (Ymax) Gage c Gage b Gage a

At a point on the free surface of an aluminum alloy (E = 10) x 10" psi and v = 1/3) machine component, the three strain gages shown in Figure below were used to obtain the following strain data: Ea = +800, Ep = +960µ, Ec = +800u Determine a) the three principal strains (E1, E2, amd E3) b) maximum shear strain (Ymax) Gage c Gage b Gage a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate true strain ASAP
4) DeterminethemaximummagnitudeofPandplottheshear-stressdistributionactingoverthesectiona-aofthe cantilevered beam if the cantilevered beam has the maximum shear stress max = 6 MPa. Specify the numerical values of shear stress at B and position of the maximum shear stress.
A compressive load P = 128kN is applied as shown below, at a point 70mm to the left and 30mm below the centroid of a rectangular section for which h=300mm and b=150mm. What additional load, acting normal to the cross-section at its centroid, will eliminate tensile stress anywhere over the cross-section.
Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses are 120MPa for bearing in the plate material and 60MPa for shearing of rivets. Determine the following:a. The minimum thickness of each plateb. The largest average tensile stress in the plate F=70
A pipe carrying water has average height of irregularities from the surface of the boundary as 0.15 mm. The shear stress developed is 4.9 N/m2 and the kinematic viscosity of water is .01 stokes. Calculate roughness Reynold number.
Describe about the effective stress path.
Explain In-Place Shear Tests—Vane Shear.
Determine poison ratio longitudinal strain 0.5 Lateral strain -0.3
a. Draw a bolt subjected to single and double shear, indicating stress distribution.b. Draw a bolt subjected to single and double support stress, including stress distribution.c. Draw stress distribution in a bar with an inclined plane.
Define Osterberg Load Cell.
A thin – walled section shown has a thickness of 12mm. It carries a vertical shear force of 5,000N. a. Compute the shear force carried by 300mm flange. b. Compute the shear force carried by the 200mm flange. c. Compute the distance between the shear center and the 300mm flange. please show COMPLETE solution
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 263 mmBeam height = 466 mmWLL = 12.52 kN/mWDL = 18.03 kN/mSpan of the beam = 11 mPrestressing force = 323 kNeccentricity = 105 mm