= 13.3 × 10-At a temperature of 32°F, a 0.09 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a6/°F] and bar (2) is stainless steel [a 7.7 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at whichthe two bars contact each other. Assume L₁ = 32 in., L₂ = 65 in.=(1)(2)BAL₁gAnswer: Final temperature = iboL2°F.

Answered: Image /qna-images/answer/17695b36-1b48-447a-bff4-afe939d8dd8b.jpg

At a temperature of 32°F, a 0.09 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 13.3 x 10- 6/°F] and bar (2) is stainless steel [x = 7.7 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 32 in., L₂= 65 in. (1) (2) B L₁ g Answer: Final temperature = i L2 °F.

At a temperature of 32°F, a 0.09 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 13.3 x 10- 6/°F] and bar (2) is stainless steel [x = 7.7 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 32 in., L₂= 65 in. (1) (2) B L₁ g Answer: Final temperature = i L2 °F.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the clamp exerts a normal force of 100N on the three pieces held together as shown. what force P may be exerted motion impends? the coefficient of friction between the pieces is .60
A rigid bar ABC is pinned at A and supported by the cables at point B as shown in the figure. The rod is pin connected. Diameter of bar is 36 mm θ. A load P equal to 100 kN is applied at C. E = 200,000 MPa. Coefficient of thermal expansion is 12x10 -6/C degrees. How to solve the displacement of C if the temperature rises by 60 degrees? Also, how to compute the tensile stress induced by the 100kN in rod BD. Compute the load P that a cable at C with a diameter of 16 mm θ can carry so that it will noy exceed a displacement of B equal to 2 mm. Neglect the thermal stress
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end. A horizontal beam BDE is pinned to the vertical bar at joint B and supported at point D. Load P2 and moment M are applied at end E. Calculate the vertical displacement δC at point C if the loads are P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi and crosssectional areas are A1 = 0.25 in2 A2 =0.15in2 .Ignore the weight of the bar.
6.78 The chain AB weighs 25 N/m. If the force in the chain at B is 4000 N, determine the length of the chain. (Ans: 26.7m)
Assume that the truss is simply supported at joints M and E. Determine the stress at member AB if Pu= 18.375 Kips, the area is 23 in². Answer your problem with the given unit ksi in 3 decimal.
Calculate the characteristic dimension of the cross-section, b, and paste the section into the form, including dimensions in [cm]. Calculations of the cross-section characteristic dimension b, and other calculations should be attached to this solution. 2. According to the instructions in the form, do the calculations in units [kN] and [cm],e.g. moments of inertia in [cm4],stress in [kN/m2]. Recalculate stress into [MPa]. A. For the structure shown:1.Determine the number of static unknowns and number of equations of equilibrium. 2.Find the reactions at supports and at hinge connections, draw FBD with depicted calculated reactions for eachframe elements separated(F1).3.Determine the functions and draw the diagrams of shear force, axial force and bending moment along the frame elements (F2-F4).Check the balance of forces and moments exerted on the node B (F5, F6). Determine the most strained section (section at which the internal forces take its maximum values).B.For the cross-section…
Figure Q1 shows a statically determinate plane truss subjected to a verticalconcentrated load at C and E. The truss is made using steel with Modulus of Elasticity is210 GPa, and the cross section area for all members are 30 mm2. Assuming P is the 10 and a is half of P, determine the vertical displacement at F. Thesolution can be based on Method of Conservation Energy or Method of Virtual Work.
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
The pin-connected bar system in Figure P14.3 is stretched 1 in. horizontally and connected to the pin sup- port 4. Determine the horizontal and vertical components of force that the support must apply to the bars. Area of bar 1 = 2 in.2 , area of bar 2 = 3 in.2 , and E = 30,000 kips/in.2 . K2x and K2y are stiffness coefficients.
The rigid bar DEFis welded at point D to the uniform steel beam AB. For the loading shown in figure 5, determine (a) the equation of the elastic curve of the beam, (b) the deflection at the mid-point C of the beam by double integration method Use E=29x106 psi and I= 2000 in4 X=4740
Solve the problem of centroid of solids and find x-bar, y-bar and z-bar.
For the beam shown in the figure determine the following: (EI = constant)a. value of EIθ at Ab. value of EIθ at Cc. value of EIδ at Bd. value of EIδ at D