AT-shaped bracket supports a 206-N load as shown. Determine the magnitude (N) of the reaction at A when a = 20°, x = 115.96 mm, y = 229.84 mm, and z = 315.67 mm. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the reaction at A using either U if upward or D if downward. 053.png ...

AT-shaped bracket supports a 206-N load as shown. Determine the magnitude (N) of the reaction at A when a = 20°, x = 115.96 mm, y = 229.84 mm, and z = 315.67 mm. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the reaction at A using either U if upward or D if downward. 053.png ...

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

All members of the truss have the same length L=4.3 m. Determine the MAGNITUDE (N) of force supported by member BD if P=609 N. Round off only on the final answer expressed in 3 decimal places.
All members of the truss have the same length L =4 m. Determine the magnitude (N) of the force supported by member BD if P = 473 N. Round off only on the final answer and expressed in 3 decimal places.
A 151.5N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tensionT2 (N) in the cable. Round off only on the final answer expressed in 3 decimal places.
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
The truss shown is subjected to forces P = 68 kN, the length L divided equally, and H = 0.6 m. If the resistance of bar 1 is 151 kN; Determine the maximum length (in meters) of the reinforcement so that the resistance of said bar is not exceeded.
The pulley system below is in static equilibrium. If the load W1 is 500 N. Determine value of the load W3 to the nearest Newton (N).
Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final answer expressed in 3 decimal places .
Determine (a) the critical load for the steel strut, (b) the dimension d for which the aluminum strut will have the same critical load, (c) the weight of the aluminum strut as a percent of the weight of the steel strut
A house with 932 kN weight is built on a steep slope defined by points A, B, and C. To help assess the possibility of slope failure (mud slide), determine the components of the weight in directions normal (perpendicular) to the slope.
Determine the magnitude of the force (lb) in member BD of the truss shown if P = 33172 lb, Q = 33205 lb, and y = 8.1 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v = 0.30). Determine the change in volume of the 50-mm gage lenght segment AB by computing the dilatation of the material. Determine the change in volume of the 50-mm gage length segment AB by subtracting the original volume of portion AB from its final volume.
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 34150 b, Q = 33650 b, and y = 7.2 ft. Round off only on the final answer expressed in 3 decimal places, Instead of units, indicate whether the force is tensile or compressive: use Tif tensile and C if compressive.