At the instant shown, the tower crane rotates about the z axis with an angular velocity ω1=0.25rad/s, which is increasing at 0.6 rad/s2. The boom OA rotates downward with an angular velocityω2=0.4 rad/s, which is increasing at 0.8 rad/s2. Determine,the Velocity Accelerationof point A located at the end of the boom at this instant.

At the instant shown, the tower crane rotates about the z axis with an angular velocity ω1=0.25rad/s, which is increasing at 0.6 rad/s2. The boom OA rotates downward with an angular velocityω2=0.4 rad/s, which is increasing at 0.8 rad/s2. Determine,the Velocity Accelerationof point A located at the end of the boom at this instant.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

186,000 m/h to km/y
Q 1(a) Use the below given data and calculate the metacentric height. Note: Explain each and every step. w= 200g W=2533.2g Displacement x (mm) 80 60 40 20 0 20 40 60 80 Tilt angle Ɵ (degree) 9.5 7.5 5.5 3 3 5.5 7.5 9.5 M.H (b) By using U-tube manometer how can you find out the pressure head? (c) If you are lacking of equipment, how can you determine the discharge of any channel?
25 - Which is a method used to determine the flow velocity and flow rate of a fluid? A) MacMichael B) Saybolt Furol Viscosity C) Engler Degree D) Vortexmeter E) Radiation Pyrometry
Equation 6.16: εT = ln(li / l0)
Answer: 57.4 ft/s=17.5m/sTorricelli's equation does not apply but the simplified Bernoulli's equation does apply.
Answer is hL = 17.6m
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.1. A schedule-40 pipe necks down from 24 in at point A to 12 in at point B. 8 *3/sec of 60°Fwater flow from point A to point B. The pressure head at point A is 20 *. FricLon is insignificantover the distance between points A and B. What are the magnitude and direcLon of theresultant force on the water? (A) 2900 lbf; toward A(B) 3500 lbf; toward A(C) 2900 lbf; toward B(D) 3500 lbf; toward B
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
r = 0.2 m T = 20 sin 5t
choose the correct answer Q1A- If the viscose force is dominate in Reynolds number, the flow will be: * a) Laminar flow b) Turbulent flow c) Transition flow d) All the answers Q1B- Chézy and manning equations are controlled in design of : * a) Water pipes network b) Open channels c) Water jet applications d) None of all above
Pls answer asap I will give good ratings A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of the jet is diverted upwards and some of it downwards. The incoming jet has a velocity U1=U1=1.6 m/s and a cross-sectional area A1A1. The jet that is deflected upwards has a velocity U2=U2= 0.7 m/s, a cross-sectional area A2=A2= 11 cm22 and is at an angle θ2=θ2= 35oo with respect to the horizontal. The jet that is deflected downwards has a velocity U3=U3= 0.9 m/s, a cross-sectional area A3=A3=14 cm22 and is at an angle θ3=θ3= 25oo with respect to the horizontal. The density of water is ρ=ρ=1000 kg/m33.see diagram attached and answer - A-Find the cross-sectional area of the incoming jet (in cm22) B- Find the horizontal force on the block (in Newtons) (Note: remember to convert the area of the jets from cm22 to m22!) c)The vertical force on the block is found to be FyFy. What velocity of the incoming jet (i.e. what value of u1u1) would be needed to…
Discuss the similarities and contrasting features in the derivations of the following equations: Piezometric head Euler's eq Bernoulli's eq Energy eq