at V = 2 m/s, T = 45°C, and atmospheric pressur over an isothermal plate at T, = 20°C. In the first case, Re, = 5 x 10°, while in the second case the flow is tripped to a turbulent state at x=0 m. At what x-location are the thermal boundary layer thicknesses of the two %3D ual2 Wbot ore th locel hoot Auves ot this loco

at V = 2 m/s, T = 45°C, and atmospheric pressur over an isothermal plate at T, = 20°C. In the first case, Re, = 5 x 10°, while in the second case the flow is tripped to a turbulent state at x=0 m. At what x-location are the thermal boundary layer thicknesses of the two %3D ual2 Wbot ore th locel hoot Auves ot this loco

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.29P: Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance...

See similar textbooks

Similar questions

Air at 20°C and 1 atm flow at 20 m/s past the flat platein Fig. . A pitot stagnation tube, placed 2 mm fromthe wall, develops a manometer head h = 16 mm of Meriamred oil, SG = 0.827. Use this information to estimatethe downstream position x of the pitot tube. Assumelaminar flow.
An airfoil is in a freestream where p.(assigned altitude)atm, p(density) (assigned altitude) kg/m3, and V 980 m/s. At a point on the airfoil surface, the pressure is 0.5 atm. Assuming isentropic flow, calculate the velocity at that point. assigned altitude 36.22km
A) What is an adverse pressure gradient, and where does it occur on an airfoil (Show that onan airfoil using a free hand sketch)?B) What causes the flow to separate from an airfoil?C) What are the two major consequences of flow separation?D) A B-2A aircraft is flying at H ft in standard day conditions at a velocity V kn. If the meanchord length is C ft.i- Find the overall or total Reynolds number for the aircraft.ii- Find the percentage of the wing chord where laminar flow is present, if Reynoldsnumber is 500,000.
Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance to the point at which the hydrodynamic boundary layers meet.
Consider two different flows over geometrically similar airfoil shapes,one airfoil being twice the size of the other. The flow over the smallerairfoil has freestream properties given by T∞ = 200 K, ρ∞ = 1.23 kg/m3,and V∞ = 100 m/s. The flow over the larger airfoil is described byT∞ = 800 K, ρ∞ = 1.739 kg/m3, and V∞ = 200 m/s. Assume thatboth μ and a are proportional to T 1/2. Are the two flows dynamicallysimilar?
The stagnation chamber of a wind tunnel is connected to a high-pressure air bottle farm which is outside the laboratory building. The two are connected by a long pipe of 4-in inside diameter. If the static pressure ratio between the bottle farm and the stagnation chamber is 10, and the bottle-farm static pressure is 100 atm, how long can the pipe be without choking? Assumeadiabatic, subsonic, one-dimensional flow
Air flows through the test section of a small wind tunnel at speed V = 7.5 ft/s. The temperature of the air is 80°F, and the length of the wind tunnel test section is 1.5 ft. Assume that the boundary layer thickness is negligible prior to the start of the test section. Is the boundary layer along the test section wall laminar or turbulent or transitional?From above problem.assume the flow remains laminar, and estimate the boundary layer thickness, the displacement thickness, and the momentum thickness of the boundary layer at the end of the test section. Give your answers in inches, compare the three results, and discuss. .
A rectangular sheet-metal duct is 200 ft long and has afixed height H = 6 in. The width B, however, may varyfrom 6 to 36 in. A blower provides a pressure drop of 80 Paof air at 20°C and 1 atm. What is the optimum width B thatwill provide the most airflow in ft3/s?
A straight-tapered flying-wing aircraft has the following characteristics: span, 20 ft; area, 100 ft2 ; root chord, 6 ft; tip chord, 4 ft; leading-edge sweep angle, 40 deg; sweep angle of line of maximum thickness, 24 deg; and Airfoil NACA 2412. Determine the wing's lift-curve slope and induced drag k value. Assume the flight Mach number is 0.25 in standard sea-level conditions.
Assuming a steady-state laminar flow, calculate the permeability from the following measurement made on core sample by using air. Flow rate = 2 cm3 /sec, T = 65°F, upstream pressure = 30 psi, downstream pressure = 14.7 psi, A = 0.004 ft2, L = 1.181 in, viscosity = 0.018 cp also calculate flow rate in bbl/day.
Consider a rectangular wing mounted in a wind tunnel. The wing model completely spans the testsection so that the flow sees essentially an infinite wing. The wing has a NACA 2421 airfoil section,a chord of 3.0 m, and a span of 20 m. The tunnel is operated at the following test conditions: P =101,000 N/m2; T = 35° C; V = 50 m/s; and µ = 1.9 * 10 -5 kg/(m s).(a) Determine the operating Reynolds number.(b) Calculate the lift, drag, and moment about the aerodynamic center for an angle of attack of 8 deg andRe=9*106(c) At a Reynolds number of 3 * 106, find the following:1) What is the stalling angle of attack for this airfoil?2) What is the angle of attack for zero lift?3) What is the lift-curve slope?
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m. Calculate the boundary layer thickness at the trailing edge of plate and drag force on one side of plate if: a. Surface of plate is smooth.b. Surface of plate is rough. The air properties at 20 °C are: Density, ? = 1.2 kg/m3 and dynamic viscosity, ? = 1.8 x 10^-5 kg/m·s and kinematic viscosity, ν = 1.516×10^-5 m2/s.