autotransformer

Q: A 100 MVA, 20 kV alternator has X1 = X2 = 0.20 pu and Xo = 0.05 pu. The neutral of the generator is…

A: The above question is based on fault analysis.Please note that all the options are wrong here as…

Q: Simplify the circuit above.

A: The given circuit needs to be reduced to get the required simplified circuit and the simplified…

Q: This figure shows a sample of power system network. Find the current supplied by the generator, the…

A:

Q: Suppose you have the following signals: c(t) = cos (2780+10°t) m(t)= cos (2n3+ 10%tf ™M Use the BPSK…

A: Since, the question posted by you has multiple sub-parts, we will solve the first three sub-parts…

Q: Consider the circuit shown below where the battery has an emf of = 15.2 V, the resistors have the…

A:

Q: For the following circuit, find the location of the operating point. In what region of bias is the…

A: Since beta (B) is not given, consider B as infinite.Therefore IB= 0.     Hence IE= IC.

Q: white noise has a 2-sided power spectral density of kW/MHz. It is passed through a low pass filter…

A: The two-sided power spectral density is 6 kW/MHz.This white noise is passed through a low pass…

Q: find in other explain to this that the answer is Vc+4i(x). ,,,,, but why it's not VL + Vc + 4i(x)…

A: The second loop is an open circuit loop. Hence the current in the second loop is zero.Hence the…

Q: Using the 74LS00 NAND gate chip, construct the circuit in the schematic and complete the…

A:

Q: Jsing two D flip-flops only, Design asynchronous Counter. The Counter counts in the sequence 1, 6,…

A: To Find:Design of an asynchronous Counter using D-Flipflops to count the sequence of,Steps…

Q: First Question: a) Find the inverse Z-transform of: z² X(z)=-1 Z 2-1 Z (2-1) (2+) F(K) A 2+1 B Z-I…

A: Z transform and inverse z transform can be calculated for part a and part b as follows

Q: Q2: Consider the rectangular loop shown in Figure below. Calculate the torque? X Z Bo=-0.6a, +0.8a,…

A: The magnetic field, B→∘=-0.6ay+0.8az T The current flowing in the loop, I=4 mA

Q: 2- Find the generator matrix for the following H matrix of LBC 1 1 11 011 101 [H] = 1 10 10 0 1 0 0…

A:

Q: Use a load-line analysis of the circuit shown in the figure below to determine the values of VDSQ,…

A: Circuit diagram is given as,

Q: Question1 A continuous-time system is designed to have impulse response of h(t) = 2e-4tu(t). For an…

A: for the given input x(t) and system impulse response h(t), to find(a) System output y(t).

Q: SIM 7.118 The NMOS transistor in the CS amplifier shown in Fig. P7.118 has V₁ = 0.7 V and V₁ = 50 V.…

A: Given dataTo find outWe have to determine the   voltage at the drain, ,  and the corresponding…

Q: PROBLEM 3 – TURN IN: Choose values for R3 and R4 so that: Vout = −5· Vin +1.5V (within 5%) in terms…

A: Given data Vout=-5Vin+1.5 V V2=5  V To find out We have to choose the value for R1, R2, R3 and R4

Q: Explain the main functions of i) the source and ii) the channel coding blocks in a modern…

A: The source coding block in a modern communication system is responsible for compressing the…

Q: J 되는

A: The differential voltage with respect to time needs to be calculated by using the charge of the…

Q: G(s) = G(s): |a+51|² (s+a+5i) (s+a-5i) = a s+a For a = 3, 4, 10 For a= 1, *** 8 (fixed complex part…

A: Here's a MATLAB program that will plot the step response of the given transfer function for…

Q: Use Laplace transform to solve the initial value problem of the ff DEs. 1. y"+y = 1; y(0) = 6, y'(0)…

A: Laplace transforms for differentiation in the time domain is given by,

Q: A diesel power station has the following data Fuel consumption/day = 1000 kg Units generated/day =…

A: It is given that:Fuel consumption/day = 1000 kgUnits generated/day = 4000 kWhCalorific value of fuel…

Q: draw this in logic circuits AB'+ A'B  please do include the truth table

A:

Q: Q3/ Let Region 1 (z 0) is characterized by & 2. Let D₁ = -30ax + 50ay + 70az nC/m² and find D₂.

A:

Q: 6. A simple capacitor filter fed by a full-wave rectifier develops 14.5 V dc at 8.5% ripple factor.…

A: given here a ripple factor is 8.5% and dc voltage is 14.5V and asked to find the output ripple…

Q: 好 2 以 认 以 2K 試 认 张 Vo

A:

Q: Calculate the Laplace Transform for 10.u(t) Formuale: 8(t)-1 u(t) eu(t). Answer: 1 S 1 S-A

A: The function is,.Formulae,

Q: Ques: Find current in 1.12. resienter using Norton's theorem 184(1) 5-42 Tsh UF www Birz www DE

A: It is given that:

Q: Solve this please (no handwritten solution)

A: In this questionWe need to determine the transfer function of the given system. We knowTransfer…

Q: In cylindrical coordinates, let p = 0 for p 1.5 mm. Find D everywhere: ly

A: Electric/Displacement flux density Electric flux lines is always perpendicular to the displacement…

Q: A 1bit modulator has the information signal! i(t) = 6sin2π * 10t + 3sin2π * 10t Calculate the…

A: The information signal i(t)= 6 sin 2 *10t+3 sin 2 *10t Step size () = 0.04 We need to find sampling…

Q: 6V 0,2K Τ 0.004 U 251 Find the U value in the circuit. 40K U10K

A: Circuit is given,

Q: Consider the signal x(n) = [1, 2, 3, 2, −1] ↑ with Fourier transform X(w). Compute the following…

A:

Q: Determine the inverse z-transform of the following: (a) X(z) = log(1 – ½⁄/z−¹) |z| 21/1/2

A:

Q: 12. For the VII characteristic shown in Fig. A, calculate the resistance of the load. V(V)* 60 40 20…

A: The V-I characteristic shown is,

Q: A 50 kg girl wearing high heel shoes balances on a single heel. The heel is circular with a diameter…

A: Pressure = Force / AreaFirst, calculate the force exerted by the girl on the floor. The force can be…

Q: 10 If x(n) = {1, 1, 1, 1} and h(n) = {2,0,0,2} ↑ a) Determine the output of system 1 what will be…

A:

Q: QI) An inductive Ioad is controlled by an impulse commutation chopper in Fig. I and peak load…

A: To find the maximum instantaneous capacitor voltage in an impulse commutation chopper circuit, we…

Q: For the following discrete-time signals, determine the z-transform, ROC and if they are BIBO stable…

A:

Q: A 400 kV transmission line is having per phase line inductance of 1.2 mH/km/phase and line…

A: It is given that: V=400 kVL=1.2 mHkmphC=12 nFkmph

Q: The time constant of an RC circuit is 330 μs. If R = 1 kΩ, calculate C.

A: Given Data: An RC circuit having, Resistor R=1 kΩ Time constant τ=330 μs To Find: The value of the…

Q: Q4. For the below circuit, determine: (a) The Thevenin equivalent circuit as seen from a-b. (b) The…

A:

Q: A 6-pole wave connected armature has 200 conductors and runs at 1000 rpm. The EMF generated is 500…

A: Poles, .Wave wound, .Armature conductors, .Speed, .EMF generated, .

Q: 4000 Find ic(t) using superposition, for i(t) = 10 cos(1000t) A and v(t) = 10 cos (t) V. 3 i(t)…

A: Given Data:An AC RC circuit with,Current source Voltage source To Find:The capacitor current by the…

Q: A Three-phase four-pole AC machine has 60 coils in the stator and each coil has 100 turns. The coils…

A:

Q: 1 Determine GIVEN: ombr a) the equivalent resistance and b) the current in each resister of the ff.…

A: It is given that:

Q: I1 and I2 ?????

A: It is given that:

Q: State Whether the following are TRUE or FALSE 1- All condition jumps are short jump. 2- MUL…

A: 1- False2-False3-False

Q: Solve and sketch Vo for the network of Figure 1 and determine the dc voltage. Vi 100 V –100 V 6 +…

A:

Q: What is f(-1) ? Hint: plug (-1) in for the variable w. f(w)=w^(2)+6w

A: The question belongs to the topic of algebra, specifically evaluating a function at a given value.…

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.