B 12 ft 16 ft 9 ft -

Q: D. Determine the maximum load P that can be applied at A without causing it to buckle. Use a factor…

A: Given     Length, L = 4 m  Assume the given beam material is steel. Therefore, Young's modulus, E =…

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at one end while fixed at the…

A: Given: The length of the rod, L = 4 m The effective length of the column pinned at one end and fixed…

Q: R17-7. The steel pipe is fixed supported at its ends. If it is 4 m long and has an outer diameter of…

A: Critical load for buckling is given by For both end fixed Effective length is L/2 Internal diameter…

Q: The steel link AB of the wire cutter has a dimensions of 3mmx 10mm, and modulus of elasticity of…

A:

Q: Determine the resulting internal loads on the cross section through point C in the grippers. It has…

A: Given Applied load = 20 N To find Freebody diagram Internal loading at C

Q: if the rods AB and BC have the same modulus of elasticity E = 210 GPa. each member has a solid…

A: Any action that can change the state of motion is called force, Force is described by its magnitude,…

Q: 17-17. The W250 × 67 is made of A992 steel and is used as a column that has a length of 4.55 m. If…

A:

Q: *R17-8. The W200 × 46 wide-flange A992-steel column can be considered pinned at its top and fixed at…

A: Write the properties of A992 steel. Write the properties of the W200X46 flange.

Q: Determine the critical buckling load for the column. The material can be assumed rigid.

A: Given data Length of the column is L Stiffness of the spring is k To determinet the critical…

Q: When we determine the allowable load on a column without buckling, we are required to use the…

A: The given statement is False.

Q: 17-31. The A-36 steel bar AB has a square cross section. If it is pin connected at its ends,…

A: Draw the free-body diagram of the bar.

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at one end while fixed at the…

A: Given data: The length of the rod is L=4 m. The axial load on the truss is P=15 kN. The factor of…

Q: Determine the maximum force P that can be applied to the handle so that the A992 steel control rod…

A: for the given figure  the FBD of rod OC will be  Balancing moment about O F*2 = P*3 F = 1.5P the…

Q: Determine the internal load of element 3. Note that elements BG and CF are independent. a = 3, b…

A:

Q: The 10-ft-long bar is made of aluminum alloy 2014-T6. If it is fixed at its bottom and pinned at the…

A: Given that,

Q: Determine the maximum allowable load P that can be applied to member BC without causing member AB to…

A: Given data To determine the maximum allowable load P that can be applied to member BC without…

Q: C. The column has a length of 15 ft. If Its ends are assumed pin supported, and It is subjected to…

A: given; length of column (l)=15ft=4.57maxial load (P)=150kip=667.23KN=667.23*103Nends are pin…

Q: 8. Select the lightest W shape that will act as a column 12 m long with fixed ends and support an…

A: To find : select the lightest shape that will act column. Given : axial loadP=700 KN proportional…

Q: The A-36 steel pipe has an outer diameter of 2 in. If it is held in place by a guywire, determine…

A: Let T be the tension in the string BC. Draw the F.B.D of the given pipe.

Q: The two members shown are all pinned jointed made of wood having square cross sections of dimensions…

A: here, P=24kN and we have to find a for both bar AB and BC with the help of Buckling formula.And…

Q: The linkage is made using two A992 steel rods, each having a circular cross section. If cach rod has…

A:

Q: Member AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins at A…

A: Given data: Channel length, l=2.5mYoungs modulus, E=200GPa

Q: Determine the relative displacement of one end of the tapered plate with respect to the other end…

A: considering free body diagram of the system calculating width…

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter of…

A: Free-body diagram of the rigid pipe is given as,     On using equilibrium of moment about A,…

Q: The linkage is made using two A992 steel rods, each having a circular cross section. If each rod has…

A:

Q: The two members shown are all pinned jointed made of wood having square cross sections of dimensions…

A:

Q: the pipe AB is screwed in tightly to a pipe flange attached to the wall. It has two forces acting on…

A: Now as per above FBDWe have∑Fx=0Rx+FBx+Fcx=0Rx+2+1=0Rx=-3 ∑Fy=0 Ry+FBy+Fcy=0 Ry+6-2=0 Ry=-4  ∑Fz=0…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 14 kN. Assume that a = 270 mm,…

A:

Q: The W12 * 50 is made of A992 steel and is used as a column that has a length of 20 ft. If its ends…

A: Write the given data: Write the properties of the given material.

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. If the wire has a diameter…

A: Given data: The diameter of the wire, d =0.25 in. Load acting on point C, P = 600 lb. For A-36…

Q: F17-4. A steel pipe is fixed supported at its ends. If it is 5 m long and has an outer diameter of…

A: Given: Steel pipe is fixed , L=5m, t=10 mm, do=50 mm, di=do-2t=50-20=30 mm Est=200 GPa and σy=250…

Q: The steel pipe is fixed supported at its ends. If it is 4 m long and has an outer diameter of 50 mm,…

A: Given Data Outer diameter, D = 50mm Length of steel pipe, L=4m=4000mm Axial load, P = 100 KN Est =…

Q: F8-13. A 100 mm long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is applied to…

A: Given:Length of rod,L=100 mmdiameter of rod,d=15 mmTensile load on rod,F=10KN=10×103 NYoung's…

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at both of its ends. If it is…

A: Given data: Length of the circular rod, L = 4 m. Safe axial load acting on the circular rod, P = 15…

Q: QS/ Determine the maximum allowable load P that can be safely supported by the frame if t = 1.5 in.…

A: Given, t = 1.5 in b = 4 in σf = 5 ksi τf = 2 ksi FOS = 1.5

Q: A 2014-T6 aluminum alloy column has a length of 6 m and is fixed at one end and pinned at the other.…

A: Solution :- Given data :- Material 2014-T6 Aluminium  L=6 m, σy=250 MPa , Eal=75.16 Pa=73.1 MPa x103…

Q: The A992 steel bar AB has a square cross section. If it is pin connected at its ends, determine the…

A: Given data: The factor of safety with respect to buckling, F.S. = 2, The thickness of steel bar AB,…

Q: 17-25. The members of the truss are assumed to be pin connected. If member GF is an A-36-steel rod…

A: Draw the FBD Apply the method sections: ∑.MB=0FGF(3)-P(4)=0FGF=1.3333P

Q: The beam is supported by the three pin-connected suspender bars, each having a diameter of 0.5 in,…

A:

Q: 5. Determine the greatest load P the frame will support without causing the A-36 steel member BC to…

A: When the threshold force is below the buckling thrust, buckling force occurs. Buckling can result in…

Q: A steel pipe is fixed supported at its ends. If it is 5 m long and has an outer diameter of 50 mm…

A: Given data: The length of pipe, l = 5 m. The diameter of the pipe, d = 50 mm. The thickness of the…

Q: Determine the maximum force P that can be applied to the handle so that the steel control rod AB…

A: Apply the moment equilibrium condition at the cantilevered end named as C.

Q: Determine the smallest diameter of the rod that will support the load of P = 3.4 kip without…

A: Given data: For the pin jointed beam, the end fixity coefficient is unity.

Q: The steel bar AB of the frame is assumed to be pin connected at its ends for y–y axis buckling. If P…

A: Given data: The magnitude of the force P is P = 18 kN. The vertical distance between C and A is yCA…

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at both of its ends. If it is…

A: Given data: The length of the rod is L = 4 m. The axial lad is Pcr = 15 kN. The factor of safety is…

Q: F3-13. A 100-mm-long rod has a diameter of 15 mm. If an axial tensile load af 10 kN is applied to…

A:

Q: Six nails are used to hold the hanger at A against the column. Determine the minimum required…

A: given Six nails are used to hold the hanger at A against the column.diameter of each nail to the…

Q: F17-5. Determine the maximum force P that can be supported by the assembly without causing member AC…

A: The length of hypotonus is AB=0.92+1.22=1.5 m Take the forces in y direction FAB0.91.5=PFAB=1.667P…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.