B- A continuous separating tank is to be designed to follow after a water washing plant for liquid oil. Estimate the necessary area for the tank if the oil, on leaving the washer is in the form of small spherical particles 5.1 * 105 m diameter, the feed concentration is 4 Kg water to 1 Kg oil, and the leaving water is effectively oil free. The mass rate of feed of solids is 200 Kg/h. Viscosity of water = 0.7*10³ N.s/m².

B- A continuous separating tank is to be designed to follow after a water washing plant for liquid oil. Estimate the necessary area for the tank if the oil, on leaving the washer is in the form of small spherical particles 5.1 * 105 m diameter, the feed concentration is 4 Kg water to 1 Kg oil, and the leaving water is effectively oil free. The mass rate of feed of solids is 200 Kg/h. Viscosity of water = 0.7*10³ N.s/m².

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.46P

See similar textbooks

Similar questions

Calculate the time taken for a 7 um radius cloud droplet to grow via condensation into a 3500 um rain droplet. Assume a super-saturation of 1.55%, a water vapour density of 3 g m-3, and a water vapour diffusion coefficient in dry air of D=24 x10-6 m2 S -1 PLEASE SHOW CALCULATION
Water at 70oC is passed through a polyethylene membrane of 25% porosity with an average pore diameter of 0.3 µm and an average tortuosity of 1.3. The pressures on the downstream and upstream sides of the membrane are 125 and 500 kPa, respectively. Estimate the flux of water in m3/m2-day.
Water at 70 °F is to be passed through a 1 micron-thick, porous PE membrane of 25% porosity with an average pore diameter of 0.3 micron and an average tortuosity of 1.3. The pressure on the downstream and upstream sides of the membrane are 125 and 500 kPa, respectively. Estimate the flow rate of water through the membrane.
Laminar flow occurs when the Reynolds number (Re*) is below 2000; turbulent flow occurs when the Reynolds number is above 2000. For the following species, determine the maximum value of the average 1D speed for which laminar flow will occur: a) Ne at 293 K where ?η is 313 ?μP and ?ρ = (PM)/(RT) through a 2.00 mm (id) pipe b) Liquid water at 293 K where ?η is 0.891 cP and ?ρ = 0.998 g/mL through a 2.00 mm (id) pipe *Re = (?ρ **d)/?η, where d is the diameter of the tube through which the fluid is flowing.
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 13 - 1
Include a brief description and the diagram of the system. Dry air at 25◦C and atmospheric pressure flows inside a 5-cm-diameter pipe at a velocity of 3 m/s. The wall is coated with a thin film of water, and the wall temperature is 25◦C. Calculate the water-vapor concentration in the air at exit of a 3-m length of the pipe.
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.
What is the friction loss in cm of water in a 2.44m diameter chimney 61m high up which gas is flowing at 9.14 m/sec? Gas density is 0.6776 kg/m3.
Determine the settling velocity of a unit-density spherical particle of 0.3 micron (µm) diameter at STP. Given: Cunningham or slip correction factor Cc for a 0.3 µm particle is 1.567 at STP. Determine the Brownian diffusion (root mean square displacement per second) of a unit-density particle of 0.3 µm diameter. Assume STP. Given: Diffusion coefficient of a unit-density spherical particle of 0.3 µm diameter is 1.23 x 10-6 cm2/s at STP
Draw a diagram to explain what it means: flow separation, the mechanism by which fluid separation occurs, and give examples of how to delay separation and its effect on resistance
Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance of 2000 m. Ifthe line is isothermal at 323.15 K and the pressure at the entry point is 750 ×103 Pa and at the exit point is 430×103 Pa, what diameter should the pipe has to ensure that the CO2 will be delivered to the end point with the pressure drop experienced. The viscosity of CO2 at 323.15 K is 1.45×10-5kg/m.s. One trial is sufficient given you tell us how you will proceed to achieve an accurate diameter estimate. Hint: for your initial guess, use D in the range of 0.01-0.02 m.
Agas at 0°C and avelocity of 2.5 m/s, flows over a 1.2 m long, 2m wide plate that is maintained at 80°C. If the gas properties are: Density = 1.142 kg/m3 , cp = 1.04 kJ/kg.K, ν= 15.63×10 -6m2 /s, k = 0.0262 W/m.K,and Pr= 0.708,determine: (a)The critical length of the flow[m] (b)The average heat transfer coefficient[W/m2 .K] (c)Total rate of heat transfer from the plate[W]