b) A continuous-time system with frequency response H (w) is called frequency-flat if the mag- nitude function |H (w)| is constant for all w. Which of the following systems are frequency-flat and why? i) The continuous-time system with impulse response h1(t) = 8(t – T). ii) The continuous-time system with impulse response h2(t) = 8(t) + 8(t – T).

b) A continuous-time system with frequency response H (w) is called frequency-flat if the mag- nitude function |H (w)| is constant for all w. Which of the following systems are frequency-flat and why? i) The continuous-time system with impulse response h1(t) = 8(t – T). ii) The continuous-time system with impulse response h2(t) = 8(t) + 8(t – T).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When the unit step function is applied to the input of the system whose block diagram is given below, the output response takes the value c (0.2) = 0.11 for t = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate.
A causal linear time-invariant continuous-time system has impulse response h(t) = e-t +sin(t) , t >= 0 Compute the output response for all t>=0 when the input is the unit-step function u(t).
The response of a system, h(t) is given as in Figure 1 below where the amplitudeof this signal is 7. Then,this system is excited by an input of x(t) = (u(t) × (u(-t)+u(t))) /1. 1)Illustrate the input signal, x(t). 2)Calculate the convolution output of the system y(t) = x(t) ∗ h(t). Nextdetermine y(t) when t is 1 sec 2)Prove the solution in Q2 is comparable when solving in frequency domain(Laplace). Next, sketch the signal for convolution output.
When the unit step function is applied to the system input given the block diagram below, the output response takes the value c (0.2) = 0.11 fort = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate
The impulse response of a continuous-time LTI system is given byh(t) = u(t) −u(t − 5) where u(t) is the unit step function.a) Find and plot the output y(t) of the system to the input signal x(t) = u(t) using the convolution integral.b) Determine stability and causality of the system.
Given a system with input x(t) and impulse response h(t) given by: x(t) = u(t) , h(t) = u(t) . Let y(t) be the output of the system. a) Find the equation of y(t) b) Sketch / Draw y(t)
The impulse response for a single input and single output linear system is given as ?(?, ?) = sin (2? - 3−2?) / 2? - 3−2?. So what is the output of the system for ? (?) = ? (?), ? (?) = ? (? - 1) and ? (?) = ? (? - 2)?
Solve All parts or will dislike answer A. Find the open-loop transfer function . Y(S) / R(S)B. Find ?(?) when the input ?(?) is a step function (use expansion of partial fractions).C. State the damping factor ?.D. Indicate whether the system is overdamped, underdamped, or critically damped.E. Indicate the natural frequency of the system ??.F. Indicate the poles and zeros of the system.G. Use the end theorem to find the steady-state value.H. Find ?(?) (use inverse Laplace transform).I. Plot the time response of the system.
For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
15 - When the unit step function is applied to the system input given the block diagram below, the output response takes the value c (0.2) = 0.11 for t = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate.A) 0.33B) 0C) 0.25D) 0.5E) 0.67
Difference equation of a discrete-time causal (right-sided) LTI system, y(n) = 2 x(n) – x(n-1) -1/4 y(n-1) + 1/8 y(n-2) is given as. a) Give the system function H(z). b) Indicate zero, poles and ROC in the Z-plane. Is the system stable? Please explain. c) Find the impulse response of the system. d) If the system is left-sided, repeat (b) and (c).
Given the plant transfer function, G(s) = 90/ s(s+4) and H(s) = 1. Obtain (i) characteristic equation (ii) damped frequency of oscillation (iii) damping ratio (iv) settling time (v) delay time