b) A junior network associate Ah Beng had set up multi-switched VLANS configuration as the master plan in Figure 1-2. Although Figure 1-2 has no problem. But he should have misconfigured the network due to a lack of experience. Currently, the result of his configuration is all switches can ping to each other, but the connectivity between the PCs is not up. Suggest and explain to him any THREE (3) probable causes for his further troubleshooting actions. VLAN 66 192 168.66.61/24 S1 Gigo/1 Gigo/2 VLAN 11 192 168.11.13/24 PCB VLAN 11 192 168.11.12/24 PCA Gigo/1 Fa0/11 $2 Gigo/2 Fa0/11 $3 VLAN 66 192 168.66.62/24 VLAN 66 192 168.66.63/24 Figure 1-2: A multi-switched VLANS network topology diagram

b) A junior network associate Ah Beng had set up multi-switched VLANS configuration as the master plan in Figure 1-2. Although Figure 1-2 has no problem. But he should have misconfigured the network due to a lack of experience. Currently, the result of his configuration is all switches can ping to each other, but the connectivity between the PCs is not up. Suggest and explain to him any THREE (3) probable causes for his further troubleshooting actions. VLAN 66 192 168.66.61/24 S1 Gigo/1 Gigo/2 VLAN 11 192 168.11.13/24 PCB VLAN 11 192 168.11.12/24 PCA Gigo/1 Fa0/11 $2 Gigo/2 Fa0/11 $3 VLAN 66 192 168.66.62/24 VLAN 66 192 168.66.63/24 Figure 1-2: A multi-switched VLANS network topology diagram

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

May someone please show me what should I input in the CLI in every task/ DIRECTION. Perform the following tasks and capture or copy the CLI commands for each indicated task. Task 1. Create VLAN’s, enable switchport mode, and assigning VLAN’s interfaces on each switch. Task 2. Configure sub-interfaces on a router with CME Task 3. Configuring a DHCP address scope on a Router Task 4. Configure Router’s Telephony Service for IP Phone Task 5. Create Directory Numbers Task 6. Verify Connectivity and Test IP Phone Communication
For over a decade, Ramanathan has been working as a network engineer in an MNC that uses FC (Fibre Channel) networking architecture. His primary duty is to ensure that there are no issues in the network connections between servers and SAN (storage area network) devices, so that maximum throughput is achieved at all times. Recently, one of the connections of the FC device to the network malfunctioned, which Ramanathan has to fix. Analyze which of the following Ramanathan should do in this scenario. a. Use NICs to connect the FC devices to the network b. Use the iSCSI protocol c. Install CNAs to connect to network servers d. Connect the FC devices to the network through HBAs Which of the following planes is made up of the physical or virtual devices that receive and send network messages on their way to their destinations? a. The control plane b. The management plane c. The application plane d. The infrastructure plane Which…
DIRECTION. Perform the following tasks and capture or copy the CLI commands for each indicated task. Task 1. Create VLAN’s, enable switchport mode, and assigning VLAN’s interfaces on each switch. Task 2. Configure sub-interfaces on a router with CME Task 3. Configuring a DHCP address scope on a Router Task 4. Configure Router’s Telephony Service for IP Phone Task 5. Create Directory Numbers Task 6. Verify Connectivity and Test IP Phone Communication Please show me the step by step
CSM Tech Publishing has expanded its network from one subnet to two subnets and is putting 200 computers on the new subnet with plans for adding up to 100 more computers over the next few years. Currently, it's using DHCP for the existing subnet and has a scope configured with start address 172.16.1.1 and end address 172.16.1.200 with a prefix length of 24. The DHCP server is in the main distribution facility where the router is placed to route between the subnets. The current DHCP server runs Windows Server 2016, is performing well, and has plenty of unused computing resources (CPU, memory, and so forth). You need to configure DHCP for the new subnet at the lowest cost possible. Propose a DHCP configuration, the scope's start and end addresses, and the prefix length for the new subnet.
You are employed as a network engineer and have been asked to analyze a communication network to determine the current data rates and ensure that the links aren’t at risk of “reaching capacity.” In the following figure of the network, the sender is transmitting data at a total rate of 100+50 = 150 megabits per second (Mbps). The data is transmitted from the sender to the receiver over a network of five different routers. These routers are labeled A, B, C, D, and E. The connections and data rates between the routers are labeled as , , , , and . Directions In this project, you will analyze the communication network and solve for the unknown data rates using a variety of techniques. The system can be modeled mathematically as a system of linear equations by writing an equation for each node/router in the network. Each of these equations can be written by noting that the sum of inputs must equal the sum of outputs. To complete the project, work on the problems described below. As you…
Ross is running a small data entry back office, for which he has contracted you for network management. Ross has made it very clear that because he has just started the company he wants to cut down on expenses wherever he can. One such option involves the router-he wants to exchange the router with a similar but less expensive alternative. Which of the following will you refer to Ross in such a situation? a. A layer 3 switch b. An SDN controller c. Storm control d. A root port Which of the following is a distinct network of storage devices that communicate directly with each other and with other portions of the network? a. SDN b. A BPDU guard c. STP d. A SAN
Which of the following assertions about circuit-switching networks is false? If the resource's owner call or host does not utilize it, it is shared. Reserve end-to-end resources if circuit-like (guaranteed) performance is required.
Consider now, that the two Access Points are within the same ISP, located in two neighboring buildings. The interconnection device between the two APs is a switch. A user may move from one AP to another when signal strength decreases as the user moves. The switch is supposed to know which AP the user is connected to. Switches are self-learning; however, they were not designed to support highly mobile users who want to maintain TCP connections while moving between APs. Describe the problem here in more detail and explain a possible solution.
You have been asked to bond/aggregate 4 of the gigabit ethernet connections between two switches to provide a total bandwidth of 4g bps between them. you notice that one of the switches is a cisco switch and the other is from a different manufacturer. what protocol should you choose in order to successfully configure port-aggregation between the switches? choose the correct option. A) FCoE B) LACP C) PAgP D) HSRP D) hsrp
in a virtual network, there are three switches k1, k2 and k3. Source P need to communicate with destination T. The input port, output port and VCI for k1 is 8,4,55, input port, output and VCI for k2 is 6,5,75 and input port,ouport and VCI for k3 is 9,7,66. Conatruct the packet switch table for k1 k2,k3 and diagramatically represent the flow of setup request and acknowledgement.
Packet Tracer File (Design your own network) Requirements: 1 Routers Configured with basic configuration 1 Switches Configured with Vlan10, within this switch 5 PC is connected (172.168.20.0/28) 1 Switches Configured with Vlan200, within this switch 2 PC is connected (192.168.50.0/29) PC from VLAN 10 should be able to Connect to PC in VLAN 200 and vice versa Both Router and Switch should have these properties. Name R1[Your Initial], S1[Your Initial], S2[Your Initial] Banner [Put your name] Passwords use this as a password to all CPENET2EXAM You can decide for other Ip addresses and VLAN Needed All configurations should be documented
James has been appointed as the service manager in one of the outlets for Grason Communication, which sells switches and routers. A client approaches James with a query from a network provider who is requesting for an alternative router that is less expensive and will work within layer 5 and layer 7 in the OSI (open systems interconnection) model. Analyze which of the following options James should present to his client in this scenario. a. Layer 4 switches b. ToR switches c. EoR switches d. Layer 3 switches As a network administrator of your company, you have decided to implement redundant connections between network devices to solve problems like network bottlenecks. You have decided to implement this change so that multiple network interfaces and ports can act as one logical interface and focus on increasing total throughput and better load balancing. Which of the following will you use to implement this change in your Windows devices? a. Load…