(B) A waveform d(t)=40sin(450t+35°) +40, is to be sampled periodically and reproduced from these sample values: . Find the maximum allowable time interval between sample values. 2. How many sample values need to be stored in order to reproduce 2 sec of this waveform if sampled according to the results in 1. 3. Determine and sketch the spectrum of the sampled signal when sampling frequency fs=750Hz.

(B) A waveform d(t)=40sin(450t+35°) +40, is to be sampled periodically and reproduced from these sample values: . Find the maximum allowable time interval between sample values. 2. How many sample values need to be stored in order to reproduce 2 sec of this waveform if sampled according to the results in 1. 3. Determine and sketch the spectrum of the sampled signal when sampling frequency fs=750Hz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given an analog signal. m(t) =5cos .2000t)+2cos(2π .4000t), for t>0, sampled at a rate of 7,000 Hz, a. sketch the spectrum of the original signal; b. Sketch the spectrum of the sampled signal up to 20 kHz; c. sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal.
A) Write the equation for the small-signal gain function ???????for the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system.
(a) You are required to implement a digital filter to suppress a high frequency noisedisturbance.(i) Describe the precaution you would take in selecting the sampling interval(ii) How may the original signal recovered from the sampled signal?
An analogue signal has a bandwidth that ranges from 15Hz to 10kHz.What is the rate of sampler and bandwidth of band limiting filter required if signal is stored within computer memory ,signal is transmitted over a network which has a bandwidth between 200Hz and 3.4kHz and what is the difference between quantization noise and signal to noise ratio expected in the transmission of signals in the above two occurrences (assuming @ signal is sampled at 8 bits per sample?
Design a single-sideband AM modulator and demodulator units based on following rules. Design Principles: bandwidth of filter you will design will be 6kHz in case of double sideband solutions. the carrier frequency is 4MHz. a) Determine the values of elements (if any; R, C, and L) used in the circuits. b) In case of noise (added to the modulated signal, What can be the SNR at i/p stage of demodulator? What can be the SNR at o/p stage of demodulator?
A subcarrier given in Eq. 4.1 is amplitude modulated by an information signal given in Eq. 4.2. The resulting AM signal is then used to amplitude modulate the signal given in Eq. 4.3 to generate a signal that is finally transmitted. Derive a mathematical expression for this final signal that is transmitted. How, in practice, can this system be made with minimum harmonic distortion? Equations for Question 04
Sketch the Vout/Vin versus frequency characteristics of an LC Bandpass filter. Show flc and fhc on the sketch and explain how they are defined. On this sketch, show the bandwidth (BW) of the filter and explain how it is defined.
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the value of the duty cycle in A? 2.What is the quantization noise in a modulator that uses a 4-bits register for the analog to digital conversion of the given sinusoidal signal?
Kindly help to answer this figure shown. Find the transfer function of the system whose signal flow graph is shown
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
Question-1) A signal with a bandwidth of 14 MHz is first passed through a low filter with a cut-off frequency of S MHz. Then the signal is sampled using the minimum sampling frequency required and each sample is coded with 8 bits. Since the minimum signal to noise ratio is used to make the efficiency of this communication channel 4 bit /s /Hz, how many MHz should the bandwidth of the channel that this signal can transmit be at least? NOTE: If the information in the text and the photo is different, please solve the question using the information given in the photo. Help me please... Thank you so much.
For the system defined by the first-order differential equation: Draw the log magnitude (dB)-log frequency graph of H(jw). (The phase graph is not required. The frequency axis is expected to be logarithmic when drawing the log magnitude graph.) The input is assumed to be suppressed when the magnitude of H(jw) is -40dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest value of wa in this case?