(b) As an electronics engineer, you are required to design IIR digital low-pass filter to meet the following specifications: Passband frequency Passband peak ripple Stopband frequency Stopband attenuation Sampling frequency 1.2 kHz 0.5 dB 2.5 kHz 50 dB 8 kHz The filter is to be designed by performing a Bilinear transformation method on an analog system function. Thus, i) Compute the filter order, N for Butterworth and Chebyshev Type I (Assume T= 0.5). ii) Compare the difference in the filter order between Butterworth and Chebyshev Type I filter.

(b) As an electronics engineer, you are required to design IIR digital low-pass filter to meet the following specifications: Passband frequency Passband peak ripple Stopband frequency Stopband attenuation Sampling frequency 1.2 kHz 0.5 dB 2.5 kHz 50 dB 8 kHz The filter is to be designed by performing a Bilinear transformation method on an analog system function. Thus, i) Compute the filter order, N for Butterworth and Chebyshev Type I (Assume T= 0.5). ii) Compare the difference in the filter order between Butterworth and Chebyshev Type I filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a fourth-order Butterworth low-pass filter with a cutoff frequency of500 Hz and a passband gain of 10. Use as many 1kΩ resistors as possible.Compare the Bode magnitude plot for this Butterworth filter with that of theidentical cascade filter.
A digital filter is described by an equation below: a)Construct the system function in H(z). b)Design the block diagram representation of the Direct Form I for the system function.
Design the following Butterworth IIR filters. Let Fs=8000Hz. Determine H(s) of the analog Butterworth prototype based on a normalized sampling frequency Fs=1Hz (to simplify the computations).NOTE: If a digital filter with fc=800Hz is to be designed with Fs=8000Hz, an equivalent filter with normalized frequencies fc=0.1Hz and Fs=1Hz can be designed instead. The normalized frequencies are computed by dividing all the original frequencies with the original Fs. Determine H(z) and the difference equation of the Butterworth IIR filter using Bilinear transformation with pre-warping.(a) 2nd-order Lowpassfc=800HzNote: The normalized frequencies are fc=0.1Hz and Fs=1Hz. Answer: H(s)= 0.4223/(s^2+0.919s+0.4223) y[n]=0.0675x[n]+0.1349x[n-1]+0.0675x[n-2]+1.143y[n-1]-0.4128y[n-2]
Design a high pass filter with a cut of frequency of K1 and a passband gain of K2. Take K1 equal to 27 in kHz and K2 is the 7 (b) Plot the Bode plot of the frequency response of the designed circuit using a python script and validate your answer. (c) How would you increase the passband gain by a factor of five without changing the cutoff frequency?
Need Help Asap What is an active low pass filter? Explain its impact and application in engineering problems.
1. How to writing the formula of convolution in spatial domain and frequency domain. a. spatial ? b. frequency? c. Which one is faster or complex? In what condition? 2. How to write the diagram of filtering operation in frequency domain? 3. Why no 2. Needs to be inverted? 4. How to mention the examples of smoothing filter and sharpening filter in frequency domain? 'All the answers based on data science image processing'
(a) Design a high-pass filter (choose R1, R2, andC) to have a high frequency input resistanceof 20 k ohm, a gain of 20 dB, and a lower cutofffrequency of 1 kHz. (b) Choose element valuesfrom the table.
The function generator circuit in the EIA has been designed to generate a sinewave output voltage with an amplitude of 5 Vat a frequency of 1 kHz. The low-pass filter hasbeen designed to have a low-frequency gain of−1 and a cutoff frequency of 1.5 kHz. What arethe magnitudes of the undesired frequency components in the output waveform at frequencies of2, 3, and 5 kHz?
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
using 1 uF capacitors and ideal op amps, design a high-pass Butterworth filter with a cutoff frequency of 8kHz and the gain is at least -85 dB at 500 Hz. A) Determine the order of the Butterworth filter. B) Calculate all components values for the design.
Design an active high-pass filter (choose the values of R1, R2, and C) with fL = 5 kHz, a high frequency gain of 20 dB, and an input resistance of 18 k at high frequencies.
A numerical filter design problem is given. This filter, which is desired to be causal and stable, suppresses 0 and π frequencies (having zero at z1=1 and z2=-1 points) and passes π/2 and –π/2 frequencies (p1=rejπ/2 and p2=re-jπ/2). have poles at the points) is desired. By choosing an appropriate r-value, the filter: a. give the system function and frequency response,b. Give the unit impulse response,c. Give the difference equation.