(b) Assuming that V3(t) = 6cos(50t – 40) V in the circuit of Figure Q4(b): - 20 oa + 4H 0.25mF q어 Figure Q4(b) (i) Convert the circuit into frequency domain. (ii) Calculate current, I. (iii) Calculate the average power, P absorbed by each of the passive elements.

(b) Assuming that V3(t) = 6cos(50t – 40) V in the circuit of Figure Q4(b): - 20 oa + 4H 0.25mF q어 Figure Q4(b) (i) Convert the circuit into frequency domain. (ii) Calculate current, I. (iii) Calculate the average power, P absorbed by each of the passive elements.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Related questions

Q: Q/ Determine i, in the circuit of Fig. below , using the superposition principle. F 10 ww 24 V 2H…

A: Superposition Theorem: In a linear active bilateral network consisting no. of energy sources,…

Q: 12. For the circuit of Fig. 13.43, (a) draw the phasor representation; (b) write a complete set of…

A: From the above figureConverting inductor and capacitors into frequency…

Q: A series-connected circuit has R = 4 22 and L = 25 mH. (a) Calculate the value of C that will…

Q: A solenoid coil has a resistance of 30 Ohms and an inductance of 0.5H. If the current flowing…

A: This question belongs to circuit theory . It is based on the concept of impedance of coil . Problem…

Q: 2. A 33 kV, 50 Hz network has a capacitance to neutral of 1.0 μF per phase. Calculate the reactance…

A: inductance of arc supression coil coil L= 13 w2c where w is the frequency in rad / sec. c is…

Q: VDD = 1.8 V RG Vino o Vout RS 50 ΩRL Given: VDD = 1.8 V, RG = 50 kOhm, RS = 100 Ohm, RL = 50 Ohm W/L…

A: We need to find out gain for given circuit.

Q: A resistor of 30 is connected in series with a capacitor of 50 µF. Calculate (a) the impedance and…

Q: A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance…

Q: ww 22.28 mH 363.66 mH 353.68uF 6020° 50 Hz 42 T212.21 pa a. For the circuit shown above, determine…

A: Resonance jωL=1jωCInductor→ shortedCapacitor→ opened The circuit is purely…

Q: Voltage Supply, VL = 450 V Frequency, Felec. = 50 Hz Resistance, R = 352 per phase Inductance, L =…

A: It is given that: VL=450 VR=35 Ω/phL=0.55 H/phfelec=50 Hz

Q: A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a…

A: Given,ZL=0.05+j0.02PL=1.0β=0.0538∠21.8°QL=0.6jPR=VsVRβcosβ-δ-AVR2βcosβ-αReal power…

Q: 19 Three impedances are connected in series across a 100 V, 2 kHz supply. The impedances comprise:…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Calculate the input impedance for the circuit shown in figure. Assume A = 0. Şekildeki devre için…

Q: Q3 For the circuit shown calculate the following :Calculate the impedance of the R = 20 X, = 60 A =…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: A coil of inductance 80 mH and resistance 60 is connected to a 200 V, 100 Hz supply. 10. Calculate…

Q: An analog receiver system consists of an antenna and three cascaded RF amplifiers as shown in Figure…

A: First we will find out noise figure for individual stage then we will find out overall noise figure…

Q: Determine vo(t) in the circuit shown in Fig.3. Hint: transform the time domain circuit to the phasor…

Q: Q.20: The voltage and current at the terminals of a network are: e=5+300cosot+100sin3@t Volt &…

Q: | Zc For the circuit given above, the circuit parameters are; Is = 3 A, ZR = 10 ohms, Zc = -j6 ohms,…

A: The value of inductance and capacitance is given in ohm that means they are in impedance form and…

Q: For a system with total complex power of 10000 + 7500j VA, nominal voltage of 250 angle 30 deg. and…

A: Capacitor- Capacitor is a device which stores the electrical energy which passes through it.

Q: +40 V kN. 1 µF 22 MQ D Vas(Th) = 5 V Vps K = 120 x 10-6 A/V² Vaso = 12.48 V 1 µF G Vị . S VGs Yos =…

A: This is a basic problem of MOSFET The solution is given below

Q: Consider the below circuit with Vs (t) = 220 cos (100t) Vrms, R=200N, L=0.2H. Find: 1. The Complex,…

A: Given v(t)=220cos(100t) VrmsR=220 ΩL=0.2 H

Q: (b) Figure QI(b) shows an AC circuit. Given the voltage, V, across the impedance Z, is 111.803 4 -…

Q: E Ę Referring to Fig. 12.87, we have, and Subtracting 10,000 210-5774 210 volts (5686+/1003) volts…

A: Given here a data and asked to explain one equation.

Q: //5 KV, 82.6bem 2. Xline= 0.4 3/km HE System Base: 100 MVA, 115 kV at bus 1. Bus 1 is voltage…

Q: A single-phase, 50 Hz, RLC circuit draws a current of 3.5 A. The value of the R, L and C are 80 N,…

A: Given that f=50HzR=80 ohmL=175 mHC= 30 μFI=3.5 A Now calculate inductive and capacitive impedance of…

Q: B Bobini A Bobini ZA atur ll 240/0° v, 50 Hz

Q: State and explain the advantages f communicating using geo- tationary satellites compared vith those…

A: to explain the advantages of communicating using geo stationary satellites compared with those whose…

Q: 1.2 kW 0.8 KVAR (cap) 100/90° V 2 kVA 4 kW 0.707 pf leading 0.9 pf lagging

A: The solution is given below

Q: Two admittances, YA = 0.3 + j0.4 and YB = 0.2 – jo.25, are %3D | connected in parallel. If the…

A: current = voltage*admittance. if teo admittances Y1 and Y2 are connected in parallel then…

Q: H.W. (1): Calculate the total impedance of the circuits of Fig. 36. Express your answer in…

Q: A 30 IL has the following data: 2L/WI 30 Q; shunt capacitive susceptance at the middle of the line,…

Q: 12. For the circuit of Fig. 13.43, (a) draw the phasor representation; (b) write a complete set of…

Q: b. Find the total impedance of the network, Zr seen by the voltage source. Figure Q3 shows the…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Suppose that the current, i, through a resistor is described by the function i(t) = (60 – t)? + (60…

Q: 10.66 At terminals a-b, obtain Thevenin and Norton equivalent circuits for the network depicted in…

Q: the circuit shown, calculate re, input impedance Z₁, output impedance Z voltage gain A, assuming r =…

Q: 1. A series-connected circuit has R= 4 Q and L = 25 mH. (a) Calculate the value of C that will…

Q: FN.Q2 – A coil of inductance 245 mH and negligible resistance is connected in series with a 56 2…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other…

Q: Calculate the equivalent impedance seen at the open terminals of the network if frequency f is equal…

Q: 1. A resistor of 50 ohms, a 200mH inductor, and a 1.5 x 10-4 F capacitor are connected in to a…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a…

Q: Q/ Determine i, in the circuit of Fig. below, using the superposition principle. 20 AF s0 cos 2000 V…

Q: A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad.…

Q: QI: Using mesh analysis, find I,in the circuit of Fig. (a) Note: Use Cramers rule. 6Ω iz 1ot 4Ω 8Ω…

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: 6A 6A AC AC ESS GEN 1 26 % 115 v 400 HZ APU GEN 0 % 116 v 400HZ GEN 2 26 % 116 v 400 HZ401 HZ 115 C…

A: External Power Unit- It is defined as the unit which is provided externally to supply energy to the…

Q: 34. A 33 kV, 50 Hz network has a capacitance to neutral of 1.0 µF per phase. Calculate the reactance…

A: Given, Capacitance, C = 1.0 µF per phase Frequency, f = 50 Hz So, ω=2πf=2π×50 radsec

Q: Given a mesh connected system with reactive factor of 60 percent and true power of 2,500 kW.…

A: We need to find out reactive power

Q: Consider the below circuit with Vs (t) = 220 cos (100t) Vrms, R=400N, L=0.2H. Find: 1. The Complex,…

Q: Calculate the input impedance for the circuit shown in figure. Assume A = 0. Şekildeki devre için…

A: Here it us asked to find out the input resistance of the amplifier. To have the input resistance we…

Question

(b)
Assuming that Vs(t) =
6cos(50t – 40) V in the circuit of Figure Q4(b):
20
O a
+
4H
0.25mF
Figure Q4(b)
(i)
Convert the circuit into frequency domain.
(ii)
Calculate current, I.
(iii)
Calculate the average power, P absorbed by each of the passive elements.
m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Enumerate five step-by-step procedures of Maximum power transfer theorem method in application to ac electric circuit problem solution or analysis
For the configuration shown in the figure below, determine Zi if Vs = 40 mV, Sense = 0.5 kΩ, and Ii = 20 µA
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall power factor is to be unity (in resonance)? The circuit is energized by a 120 volt, 60 cps source. 2. The given figure is to be designed to pass a wave having a frequency of 3500 cps and block a 2500 cps wave. The series inductor has an inductance of 0.0023 henry. Calculate the capacitance of the series capacitor and the parallel inductor.
6.23 Find period, frequency, phase angle in degrees, and maximum, minimum, average, and effective values of vðtÞ ¼ 2 þ 6 cosð10t þ =6Þ. Ans: T ¼ 0:2 s; f ¼ 5 Hz; phase ¼ 308; Vmax ¼ 8; Vmin ¼ 4; Vavg ¼ 2; Veff ¼ ffiffiffiffiffi 22
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
POWER SİSTEMS high voltage technique it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approximate impulse,AC AND DC voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE SAME QUESTION FOR DC HİGH VOLTAGE AND AC HİGH VOLTAGE WHAT THE DIFFERENCE BETWEEN THEM
In layman's terms, Give a summary of the concepts of phase modulation.
characteristic impedance z0 = 50 ohms is a short-circuited coaxial (coaxial) cable with a length d = 0.3λ component is wanted to be made. Use Its frequency is f = 8 GHz. (a) Identify the component. (b) Find the impedance value of the component. (c) Find the parameter value of the component. lesson:electrical and electronical engineering
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, what is the amplitude, phase angle and angular frequency values of the circuit that will pass through the circuit? AB=06, BA=60
Explain in detail (no mathematical expressions) the following termsused in microwave theory: Characteristics impedance, Dominantmode, Impedance matching, Characteristics admittance
Q10. If the impedance of a circuit = 20 – j10n, if a voltage source is connected across this impedance, which if the following statements is correct?